9
An empty or partially empty spa of water during sunlight hours can cause deforming, melting, crazing,
discolouration, blisters or holes in the spa’s fiberglass, acrylic and fittings, this can happen within minutes of
the spa being emptied or partially empty. Your warranty does not cover deforming, melting, crazing,
discolouration, blisters or holes in the spa’s acrylic and fittings, so it is especially
important your hardcover is on the spa when not in use and the spa is filled with
water at all times during daylight hours.
To locate your drain fitting it will be found on the touchpad side of the spa in either
the left or right hand corner of the black fibreglass base underneath the synthetic
cabinet. When you want to operate the drain fitting turn the handle clockwise and
at the same time pull the handle away from the spa to release it from the locking
keyway. When the drain fitting is pulled fully away from the fibreglass base you
can now unscrew and remove the handle by screwing it anticlockwise. With the
handle off you can now connect the supplied hose connection and attach your
garden hose, now push the drain halfway back in toward the fibreglass base and it will begin draining the
spa. Once drained remove the garden hose and garden hose connection. Replace the handle by screwing
it on clockwise and push the drain fitting back into the fibreglass base. Once in the fibreglass base slightly
turn the handle which will prevent it from coming out when you refill the spa with water.
TURNING JETS ON & OFF
The larger jets in your spa can be turned on or off. Turning the jet face clockwise will turn the jet on which
will allow the water to flow through the jet. Turning the jet face anticlockwise will turn the jet off stopping the
water from flowing through the jet. The smaller jets in your spa can not be turned on and off, they will
always remain on.
WATERFALL CONTROL HANDLE
Your waterfall control handle can be located on the spa image on page one.
When using this handle do not apply pressure to the handle at the fully open or fully closed positions you
will break the handle if you do.
To run your waterfall turn the manual heating button on and set the temperature button at least two degrees
above the current water temperature, then turn the waterfall control handle anticlockwise. To turn the
waterfall off turn the waterfall control handle clockwise until the waterfall stops running. Reduce the
temperature button back to the original temperature.
AIR CONTROL HANDLE
The air control handle can be located on the spa image on page one.
This handle controls the amount of air pressure coming from the jets, which will increase the water pressure
if it is turned anticlockwise and will decrease the water pressure if it is turned clockwise.
MAIN WATER DIVERTER
The main diverter handle can be located on the spa image on page one.
Do not turn this handle while the pumps are running and do not apply pressure to the handle at the fully
open or fully closed positions you will break the handle if you do.
This handle is used to divert the water within the spa, when you turn the handle to different positions the
water pressure will change within the spas chairs. This handle will make noise when the pumps are
running, and the noise level will vary depending on where the handle is positioned.
AROMATHERAPY CONTROL HANDLE
Your spa has an inbuilt aroma therapy stick which can be located on the spa image on page one. With all
the pumps turned off unscrew the fitting from the spa and take out the stick. Remove the plastic transport
cover by unscrewing the blue cap and sliding the opaque cover off to expose the scented stick inside,
screw the blue cap back onto the aroma stick leaving the opaque cover off. Reinstall the stick back into the
spa, do not overtighten the fitting it only needs to be lightly tightened. Turning the handle clockwise runs the
aroma scent when you have the air blower turned on and turning the handle anticlockwise will turn the
aroma scent off.
MY SPA IS TOO HOT IN SUMMER, THE TEMPERATURE OF THE WATER IS HIGHER THAN I HAVE SET
During summer there may be times when the spas water exceeds the set temperature. This is not a fault in
the spa it is simply the ambient air temperature causing this. To combat this problem, you can use ice to
cool down the water.
