2
GB
Heater 55W / 100W / 150W / 200W / 300W
•
Never remove the heater from the aquarium when it is turned on.
•
Once installed, allow 10 to 15 min before turning the heater on, and
allow the same amount of time before removing the heater from the
aquarium.
Read and follow all the instructions, even if you feel you are familiar with the
product and fi nd a place to keep the instructions handy for future reference.
Your attention is drawn particularly to the sections concerning “IMPORTANT
SAFEGUARDS” and the “GUARANTEE CONDITIONS”. Please ensure you
retain your original purchase receipt in the event that guarantee service is
required.
Carefully unpack the product making sure you keep all the packing material
until all the parts of the product have been found and the product has been
assembled.
This product was packaged in excellent condition in the factory. Should you
fi nd that the product is damaged, has been dropped, or malfunctions in any
way, contact the retailer where the product was purchased, for inspection.
Please insure you retain your original purchase receipt in the event that
warranty service is required.
Before First Use / Preparation
Hints & Tips for Best Results
Trouble Shooting
Important Safeguards
To guard against injury, basic safety precautions should be observed,
including the following:
1. Read and follow all safety instructions and important notices in these
instructions as well as on the product itself.
2. This appliance is not intended for use by children or infi rm persons without
supervision. Young children should be supervised to ensure that they do not
play with the appliance.
3. To avoid possible electric shocks, special care should be taken since water
is employed in the use of aquarium equipment. For each of the following
situations do not attempt repairs yourself. Return the appliance to an
authorised service facility for service or discard the appliance.
a. If the appliance or any electrical component of the appliance (non-
immersible equipment only) falls into the water or gets wet, do not reach for
it. Unplug it and then retrieve it.
b. If the appliance shows any sign of abnormal water leakage, immediately
unplug it from the power source
c. Carefully examine the appliance after installation. It should not be plugged
in if there is water on parts which are not intended to be wet.
d. Do not operate the appliance if it has a damaged cord or plug, or if it is
malfunctioning, or dropped or damaged in any manner.
4. A “drip loop” (see graphic) should be arranged for each cable connecting
an aquarium to a power supply. The drip loop is the part of the cable below
the level of the power supply. It prevents water travelling down the cable and
coming into contact with the power supply. If the plug or the socket does get
wet, do not unplug the appliance. Disconnect the fuse or circuit breaker that
supplies the power to the appliance, then unplug and examine for presence
of water in the socket.
5. Always unplug the appliance from the electrical outlet when not in use,
before putting on or taking off parts, before any type of maintenance or
cleaning.
6. Never yank the cable to pull it from the socket. Pull the plug carefully to
disconnect.
7. Do not use the appliance for reasons other than the intended use. The use
of attachments that are not recommended or sold by the manufacturer may
cause the product to be unsafe. This is not recommended.
8. Do not install or store the appliance where it will be exposed to weather or
temperatures below freezing.
9. Make sure any component mounted on a tank is securely installed before
operating it.
10. Ensure input voltage is the same voltage as your local power supply.
11. If an extension cable is used it should have the proper rating. Care should
be taken to arrange the cord so that it will not be tripped or pulled.
12. A G.F.C.I (Ground fault circuit interrupter) & surge protector is
recommended for all electrical appliances.
13. Ensure your hands are dry when turning the power switch on/off and
when inserting/removing the power cable from the socket.
14. If you are in any doubt about the electrical installation or safety of this
product you must consult a qualifi ed electrician.
For Guarantee Conditions,
please refer to the Guarantee
form that is enclosed with
this product.
HEATER DOES NOT WORK
1. Ensure the plug is inserted correctly and the switch is in the on position.
THE LED IS WORKING, BUT THE HEATER IS NOT HEATING THE
AQUARIUM
1. Check that the control knob is set on the desired temperature.
2. Double check the thermometer. Use a second one.
3. Ensure the thermometer is not near the heater. Relocate the thermometer
to the opposite end of the aquarium.
4. Return the unit to the place of purchase for further inspection.
THERE IS WATER INSIDE THE HEATER
1. Turn the power off at the main power supply, unplug the unit and remove
it from the aquarium. If the unit is still under guarantee return it to the place
of purchase for further inspection, Other wise cut the cord and dispose of
sensibly
All products are supplied with fi tted plugs. This plug should not be tampered
with in any way or removed. Removal or tampering with the plug invalidates
our guarantee offered with this product.
For UK a 3 pin adaptor is supplied with the product and this must be used.
