Aqua Creek Products Scout Hi F-802SCNA-HLD Скачать руководство пользователя страница 3

Страница: 3 / 21

V:1.0

Revised 12/11/14

V:1.0

Scout Hi-Lift

Check entire box and inside all packing materials for parts. Before beginning assembly,

read the instructions and identify parts using the figures and parts listed in this document.

It is critical all parts be carefully inspected by the installer prior to installation to ensure

no damage occurred in transit and a damaged part is not used. If any damage occurred in

transit, Aqua Creek Products, LLC must be notified within three days of receipt of unit.

Proper installation cannot be overstressed, as an improper installation voids Aqua Creek’s

warranty and may affect the safety of the user.

READ CAREFULLY

1. THE SCOUT HI-LIFT MAIN
ASSEMBLY
2. CONTROL ARM
3. LIFTING ARM
4. HI-LIFT SEAT ARM
5. LEGREST
6. ACTUATOR
7. HANDSET
8. 24 V BATTERY

Содержание Scout Hi F-802SCNA-HLD






















Результаты поиска

Содержание Scout Hi F-802SCNA-HLD

Отзывы:

Похожие инструкции для Scout Hi F-802SCNA-HLD

Бренды по названию

Популярные бренды

Aqua Creek Products Scout Hi F-802SCNA-HLD, Руководство пользователя

Результаты поиска

Содержание Scout Hi F-802SCNA-HLD

Отзывы:

Похожие инструкции для Scout Hi F-802SCNA-HLD

Бренды по названию

Популярные бренды