background image

l

Connect the regulator to the unit, connect gas and check for leaks. 

WARNING:

 Do not use an open 

flame to check for leaks. 

l

Check the system pressure. With the front panel removed remove the plug                                                

from the manifold.

l

Place a fitting in the plug opening and connect a manometer. 

l

For  Natural  gas  the  pressure  in  the  manifold  should  be  5”  water  column  or           

12.4 millibar. For LP the pressure in the manifold should be 10” water Column or 
24.9 millibar. 

l

To adjust the pressure remove the brass cap and turn the white plastic part inside 

the stem of the regulator. See picture regulator 8. 

l

Take a wide straight screw driver and place it in the two notches shown in picture regulator 7 turn 

clockwise to increase pressure and counter-clockwise to reduce pressure. See picture regulator 8. 

l

Once the pressure has been adjusted replace the brass cap. 

l

Note the blue cap on the regulator, this is the vent there are openings below the top rim. 

NEVER

 block 

these openings your regulator will fail to operate correctly. On at least a monthly basis blow off any dust 
or grease which may accumulate around this cap. The openings must remain open for the regulator to 
function. Clean more often in a very greasy atmosphere. 

8

NAT

LP

CONVERSION

l

Instructions are for conversion from Natural Gas to Propane (L.P.) on all models HMG.

l

The conversion should be done before connecting the unit to the gas supply.

l

Units are shipped from the factory equipped for use on natural gas. Orifices necessary for LP (propane) 
are provided in a bag tied to the valve on the front panel.

1. Remove the knobs and front panel.
2. Remove the orifice fittings from the valve. Change the orifices to the size recommended for 

propane (L.P.).

3. Replace the orifice fittings into the valve.

l

To change the regulator:

1. Remove brass 

cap

2. Locate the plastic 

part attached to the 
brass cap

3. This is the natural 

gas position

4. Snap the plastic 

part off of the brass 
cap

5. Flip the plastic part  

over & snap the        
plastic part onto the 
brass cap in the        
opposite direction

6. Note you can read 

LP on the plastic 
part it is now in the 
LP position

7. Replace the brass 

cap back into the 
body of the 
regulator

8. To adjust pressure:   

Remove brass cap &  
turn white plastic 
part inside the stem 
of regulator

Содержание HMG-2424






















Отзывы: