2. B2 green/black: Ground connection
DIAGNOSIS INSTRUMENT: PARAMETERS
Engine temperature:
•
Example value with key ON: 25° C
•
Example value with engine on: 75° C
•
In case of recovery, this value is set by the control unit: if there is a malfunction after engine
start-up, temperature decreases up to approximately 75°.
Engine temperature pre Recovery:
•
Example value with key ON: -40° C
•
Example value with engine on: -40° C
•
Value drawn from the signal read without taking into account any recovery: the value in the
example refers to an open circuit.
Engine temperature at start-up:
•
Example value with key ON: -40° C
•
Example value with engine on: 25° C
•
The temperature value is stored during engine start-up. With key ON, value -40°C is read.
CAUTION
BEFORE CARRYING OUT ANY TROUBLESHOOTING, CAREFULLY READ THE GENERAL TROU-
BLESHOOTING CONCEPTS FOR ELECTRICAL DEVICES AT THE BEGINNING OF THE CHECK
AND CONTROL SECTION IN THE ELECTRICAL SYSTEM CHAPTER.
DIAGNOSIS INSTRUMENT: ELECTRICAL ERRORS
engine temperature sensor P0115
•
open circuit, shorted to positive / shorted to negative.
Error cause
•
If the circuit is open, shorted to positive: excessive voltage has been detected at PIN 12 of
the ENGINE connector. If shorted to negative: voltage equal to zero has been detected. The
instrument panel does not indicate the presence of this error even in the ATT status.
Troubleshooting
•
If the circuit is open, shorted to positive: check the sensor connector and the Marelli control
unit connector. If they are OK, check sensor continuity: replace the sensor if not OK; if OK,
check continuity between the ENGINE connector PIN 12 and the sensor PIN 1: restore cable
harness if there is not continuity; if it is OK, reconnect the control unit connector and, with
key set to key ON, check the continuity between the sensor connector PIN 2 and the vehicle
ground connection: if OK, it means that the error cause is that the cable is shorted to positive
and it is necessary to restore the cable harness between ENGINE PIN 12 and sensor PIN
1; if there is no continuity with the ground connection, check the sensor connector and the
Marelli control unit connector. If not OK, restore the cable harness. If OK, check continuity
RSV4 Factory
Electrical system
ELE SYS - 167
Содержание RSV4 FACTORY
