manualshive.com logo in svg

APRILIA RS 660, Руководство по обслуживанию станции

Модель Aprilia RS 660 - это стремительный и стильный спортивный мотоцикл, оборудованный передовой технологией. Для обслуживания и ремонта этого мотоцикла рекомендуется загрузить бесплатное руководство по обслуживанию на нашем веб-сайте. {Ссылка на скачивание руководства} Здесь вы найдете все необходимые инструкции и советы по техническому обслуживанию.

Поделиться
Скачать
background image

Scheduled maintenance table

NOTE

HALVE THE SERVICE INTERVALS INDICATED IF THE VEHICLE IS USED IN PARTICULARLY
RAINY OR DUSTY CONDITIONS, ON POOR ROADS OR FOR HIGH PERFORMANCE RIDING.

NOTE

THE TIMES LISTED ON THE SCHEDULED MAINTENANCE TABLE INCLUDE TIME DEDICATED
TO MANAGEMENT ACTIVITIES.

I: CHECK AND CLEAN, ADJUST, LUBRICATE OR REPLACE, IF NECESSARY

C: CLEAN, R: REPLACE, A: ADJUST, L: LUBRICATE

(1) Check and clean and adjust or replace, if necessary, before every journey.

(2) Check and clean, adjust or replace if necessary every 1,000 km (621.37 mi).

(3) Replace at whichever of the following occurs first: 40,000 km (24,854.85 mi) or 4 years.

SCHEDULED MAINTENANCE TABLE

Km x 1,000 (mi x 1,000)

1 (0.6)

10

(6.2)

20

(12.4)

30

(18.6)

40

(24.9)

EVERY

12

MONTH

S

EVERY

24

MONTH

S

Rear shock absorber (bearings - linkage mechanisms)

I

I

I

I

Motorcycle set up

I

I

I

I

I

Spark plug

R

R

Drive chain (2)

I - L

I - L

I - L

I - L

I - L

I

I

Clutch cable

L

L

L

L

L

L

L

Front sprocket - rear sprocket - Chain slider

I

I

I

I

Steering bearings and steering play

I

I

I

I

I

I

I

Wheel bearings - Wheels

I

I

I

I

I

I

I

Diagnosis by tool

I

I

I

I

I

I

I

Brake discs - Brake pads wear (1)

I

I

I

I

I

I

I

Air filter

I

R

I

R

Engine oil filter

R

R

R

R

R

R

R

Raked

I

I

I

I

Vehicle general operation

I

I

I

I

I

I

I

Valve clearance

A

A

Cooling system

I

I

I

I

Brake systems

I

I

I

I

I

I

I

Safety switches (stand, stop, clutch, extra negative stroke,
gas control)

I

I

I

I

I

I

I

Brake Fluid

I

I

I

I

I

I

R

Coolant

I

I

I

I

I

I

R

Fork oil (3)

R

Engine oil

R

R

R

R

R

R

R

Headlight aiming

I

I

I

I

Fork oil seals

I

I

Tyres - pressure / wear (1)

I

I

I

I

I

I

I

Nut/bolt tightness

I

I

I

I

I

Labour time (minutes)

90

110

190

110

280

80

130

NOTE

AT EACH SCHEDULED MAINTENANCE MUST BE VERIFIED WITH THE DIAGNOSTIC TOOL IF
THERE ARE ERRORS AND THE IF THE PARAMETERS ARE CORRECT.
ENSURE THAT THE VEHICLE CALIBRATION IS UP TO DATE AFTER UPDATING THE DIAGNOS-
TIC TOOL.

SCHEDULED MAINTENANCE TABLE RESERVED FOR THE US-LATAM MARKET

I: CHECK AND CLEAN, ADJUST, LUBRICATE OR REPLACE, IF NECESSARY

C: CLEAN, R: REPLACE, A: ADJUST, L: LUBRICATE

RS 660 - Tuono 660

Maintenance

MAIN - 55

Содержание RS 660





































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RS 660

Ohlins HO 743 Mounting Instructions preview
HO 743
Бренд: Ohlins Страницы: 8
hepco & becker 6537543 00 01 Mounting Instructions preview
6537543 00 01
Бренд: hepco & becker Страницы: 6
hepco & becker Easyrack 6622520 01 01 Mounting Instructions preview
Easyrack 6622520 01 01
Бренд: hepco & becker Страницы: 4
R&G CP0485 Fitting Instructions Manual preview
CP0485
Бренд: R&G Страницы: 47
Cake Kalk Manual preview
Kalk
Бренд: Cake Страницы: 12
SRC KTM390-14-01-SL Quick Start Manual preview
KTM390-14-01-SL
Бренд: SRC Страницы: 4
Rekluse CoreManual TorqDrive Installation & User Manual preview
CoreManual TorqDrive
Бренд: Rekluse Страницы: 20
Yamaha YZ85(A) Owner'S Manual preview
YZ85(A)
Бренд: Yamaha Страницы: 86
Yamaha YZ85(B) Owner'S Manual preview
YZ85(B)
Бренд: Yamaha Страницы: 88
Yamaha YZ85(D) Owner'S Manual preview
YZ85(D)
Бренд: Yamaha Страницы: 88
Yamaha Star XV17PCX Owner'S Manual preview
Star XV17PCX
Бренд: Yamaha Страницы: 100
Yamaha Road Star XV17AWX Owner'S Manual preview
Road Star XV17AWX
Бренд: Yamaha Страницы: 110
Yamaha YZ450F(W) Owner'S Service Manual preview
YZ450F(W)
Бренд: Yamaha Страницы: 650
Barton FR 50 ccm User Manual preview
FR 50 ccm
Бренд: Barton Страницы: 35
Faller 190119/1 Manual preview
190119/1
Бренд: Faller Страницы: 8
BMW Motorrad R 1150 RT Supplementary User'S Manual preview
R 1150 RT
Бренд: BMW Motorrad Страницы: 28
BMW Motorrad G 310 GS Rider'S Manual preview
G 310 GS
Бренд: BMW Motorrad Страницы: 170
APRILIA ETV mille Caponord Use And Maintenance Book preview
ETV mille Caponord
Бренд: APRILIA Страницы: 384

Бренды по названию

Популярные бренды

Загрузить еще бренды