APRILIA RS 660 Скачать руководство пользователя

Страница: 139 / 420

Checking the secondary shaft

Characteristic

Maximum wear limit for selector gear splines

5.3 mm (0.21 in)

Minimum wear limit of the pinion side secon-
dary shaft seat

29.97 mm (1.18 in)

Minimum wear limit of the clutch side primary
and secondary shaft seat

19.97 mm (0.79 in)

Checking the desmodromic drum

•

Check the gearbox drum for any signs of damage, scratches or wear, and change the des-

modromic unit if necessary.

•

Check the desmodromic segment for any signs of damage and wear, and replace it if nec-

essary.

•

Check the desmodromic drum bearing for any signs of damage or pitting, and change the

drum if necessary.

Characteristic

Maximum selector shaft eccentricity

0.2 mm (0.0079 in)

Checking the forks

The purpose of the springs at the end of the gearbox control rods is to reduce vibration and make it

easier to engage the gears.

Characteristic

Maximum endfloat of selector forks

0.05 mm (0.0020 in)

Minimum wear limit of selector fork guide pins

6.8 mm (0.27 in)

Maximum eccentricity of the two fork guide shafts

0.05 mm (0.0020 in)

NOTE

THE FOLLOWING PROCEDURE IS VALID FOR ALL THE GEARBOX FORKS.

•

Check for damage, deformation and/or signs of wear on the roller of the gear fork cam and

on the gear fork tooth.

•

Replace the gearbox fork if necessary.

RS 660 - Tuono 660

Engine

ENG - 139

Содержание RS 660





































































































































































































































































































































































































































Результаты поиска

Содержание RS 660

Отзывы:

Похожие инструкции для RS 660

Бренды по названию

Популярные бренды

APRILIA RS 660, Руководство по обслуживанию станции

Результаты поиска

Содержание RS 660

Отзывы:

Похожие инструкции для RS 660

Бренды по названию

Популярные бренды