APRILIA Caponord 1200 2016 Скачать руководство пользователя

Страница: 226 / 573

•

short circuit to positive/ short circuit to negative / open circuit

Error cause

•

If shorted to positive: excessive voltage has been detected at PIN 61 of the VEHICLE con-

nector. If shorted to negative: no voltage has been detected. If the circuit is open: 5V voltage

has been detected. Error recognition carries out only when the fan relay is activated.

Troubleshooting

•

If shorted to positive: check the relay electrical specifications are correct by disconnecting

it from the cable harness. If not OK, replace the relay; if OK, restore the cable harness (Brown

cable)

•

If shorted to negative: check the relay electrical specifications are correct by disconnecting

it from the cable harness. If not OK, replace the relay; if OK, restore the cable harness (Brown

cable)

•

If the circuit is open: check the relay electrical characteristics are correct by disconnecting

it from the cable harness; if not OK, replace the relay, if OK, check relay connector and

VEHICLE connector of the Marelli control unit: if not OK, restore; if OK, check continuity of

cable harness (Brown cable)

RUN/STOP switch

Function

It tells the control unit if the rider wishes to enable

engine start-up or to keep the engine running.

Operation / Operating principle

If the rider wants to shut off the engine or to disable

engine start-up, the switch should be open, i.e.

VEHICLE connector PIN 78 of the Marelli control

unit must not be connected to ground.

Level in electrical circuit diagram:

Start-up enabling switches

Location:

•

on the vehicle: right light switch.

•

connector: at the centre between air fil-

ter box and water radiator.

Electrical specifications:

•

STOP position: the circuit is open

•

RUN position: closed circuit (continui-

ty)

Electrical system

Caponord 1200 - Caponord 1200 Rally

ELE SYS - 226

Содержание Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Caponord 1200 2016

Отзывы:

Похожие инструкции для Caponord 1200 2016

Бренды по названию

Популярные бренды

APRILIA Caponord 1200 2016, Руководство пользователя

Результаты поиска

Содержание Caponord 1200 2016

Отзывы:

Похожие инструкции для Caponord 1200 2016

Бренды по названию

Популярные бренды