manualshive.com logo in svg

Aprilaire 8800, Руководство программиста

Поделиться
Скачать
Aprilaire 8800 Скачать руководство пользователя страница 26

flTAlM
WPAlM
DEHAlM
SySAlM

Air filter alarm status
Humidifier alarm status
Dehumidifier alarm status
HVAC system alarm status

COS: C14

Permissions: Read/Write

Query 
Command

Syntax: 

SN[#] [alarm]ALM?<CR>

Description:  Requests the 

[alarm]

 alarm status .

Assignment 
Command

Syntax: 

SN[#] [alarm]ALM=[value]<CR>

Description:  Sets the 

[alarm]

 alarm status to 

[value]

 .

Examples: 

SN1 WPALM=ON<CR>

 

  

SN1 DEHALM=OFF<CR>

Response or 
COS Message

Syntax: 

SN[#] [alarm]ALM=[value]<CR>

Example: 

SN1 FLTALM=OFF<CR>

 

   

Node address 1 responds with an air filter alarm status of OFF .

Parameters 

Range

alarm:

 alarm command code 

[FLT, WP, DEH, SYS]

value:

 alarm status 

[OFF, ON] 

 

OFF:

 the [alarm] alarm is not active 

 

ON:

 the [alarm] alarm is active

The alarm statuses can be cleared through the Setup Screens and Menu Screens . When an assignment command is received with the value 
parameter set to OFF and the specified alarm is active, the respective alarm is cleared and reset if the alarm period is not set to OFF . When 
an assignment command is received with the value parameter set to ON and the specified alarm is not active and the specified alarm period 
is set to OFF, the respective alarm is activated and displayed on the screen . If the alarm status is changed at the node, a C14 COS unsolicited 
message is issued (if C14 is ON) .

 

HUMTyP

Humidifier type

COS: N/A

Permissions: Read/Write

Query 
Command

Syntax: 

SN[#] HUMTYP?<CR>

Description:  Requests the humidifier type setting .

Assignment 
Command

Syntax: 

SN[#] HUMTYP=[value]<CR>

Description:  Sets the humidifier type setting to 

[value]

 .

Example: 

SN1 HUMTYP=0<CR>

Response

Syntax: 

SN[#] HUMTYP=[value]<CR>

Example: 

SN1 HUMTYP=0<CR>

 

   

Node address 1 responds with a humidifier type setting of flow-through .

Parameters 

Range

value:

 humidifier type setting code 

[0 – 1] 

 

0:

 flow-through type 

 

1:

 drain-less type

26

Содержание 8800

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды