Applied Motion Products Si5580 Скачать руководство пользователя страница 20

Страница: 20 / 26

-19-

Flush Mounting

When you remove the MMI from the shipping carton, you will notice that it has two parts. The first

is a fairly thin section that contains the keypad, display and some circuit boards. The other part is

thicker and contains the telephone jack and a cable that connects to the keypad assembly.

When you flush mount the MMI in a panel, only

the thin section will stick out from your panel - the

large portion mounts behind your panel. You’ll

need to cut a precise section from your panel.

There is a cardboard template in the MMI’s ship-

ping box for this purpose.

If you want the MMI to be dust proof and watertight,

you must place the black rubber gasket between the

thin part of the MMI and your panel. Assemble the

two halves using the eight small screws provided.

Surface Mounting

An easier way to mount the MMI is to bolt the two halves together ahead of time, using the eight small

screws. If you want the MMI to be dust proof and watertight, put the black rubber gasket between the

two halves before screwing them together.

Then cut a hole in your panel for the cable that runs

between the MMI and the Si5580. The hole must

be at least 5/8” in diameter for the connector to

fit thorugh. You will also need two holes that line

up with the big mounting holes in the MMI. The

mechanical outline on page 21 shows the location

of the big mounting holes.

YES

SPACE

BKSP

ENTER

panel

MMI
(front section
and gasket)

MMI
(rear section)

YES

SPACE

BKSP

ENTER

panel

sealant (not included)

MMI

gasket
(included)

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание Si5580



























Результаты поиска

Содержание Si5580

Отзывы:

Похожие инструкции для Si5580

Бренды по названию

Популярные бренды

Applied Motion Products Si5580, Руководство пользователя

Результаты поиска

Содержание Si5580

Отзывы:

Похожие инструкции для Si5580

Бренды по названию

Популярные бренды