Applied Biosystems GeneAmp PCR System 9700 Скачать руководство пользователя страница 38

Страница: 38 / 132

3-10 Instrument Setup

Turning the

Run-Time Beeper

On or Off

When turned on, the run-time beeper beeps during a pause and once at the
completion of a run. The default value is Off.

Setting the Pause

Time Out

The Pause Time Out field sets the time in minutes:seconds format for the length of a
pause when you use the Pause soft key to pause a run from the Run Time screen. For
more information on Pausing a Run, see “Pausing a Run” on page 4-8.

To turn the Run Time-Beeper on or off:

Step

Action

Select the

Run Time Beep

field. This changes the value of the soft keys.

You can take the following action:

Press

Enter

to accept your entry.

If you want to...

Then...

turn the beeper on

Press ON.

turn the beeper off

Press Off.

To set the pause time out:

Step

Action

Select

More

to display the second configuration screen.

Set the

Pause Time Out

field by using the numeric keys to enter a time in minutes

and seconds.

From this screen, you can also define the:

♦

Idle state setpoint temperature.

♦

Baud rate for your printer port.

Press

Accept

when all information on this screen is correct.

Note

clears an entry.

Instrument Configuration

Pause Time Out: 10:00 (00:01-99:59)
Idle State Setpoint: 25.0°C (4.0-99.9)
Baud Rate: 9600

Cancel

Содержание GeneAmp PCR System 9700





































































































































Результаты поиска

Содержание GeneAmp PCR System 9700

Отзывы:

Похожие инструкции для GeneAmp PCR System 9700

Бренды по названию

Популярные бренды

Applied Biosystems GeneAmp PCR System 9700, Руководство пользователя

Результаты поиска

Содержание GeneAmp PCR System 9700

Отзывы:

Похожие инструкции для GeneAmp PCR System 9700

Бренды по названию

Популярные бренды