Applied Biosystems 7300 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 174

Applied Biosystems 7300 Скачать руководство пользователя страница 25

Safety and EMC Compliance Information

Workstation Safety

Applied Biosystems 7300/7500/7500 Fast Real-Time PCR System Installation and Maintenance Guide

xxv

Workstation Safety

Correct ergonomic configuration of your workstation can reduce or prevent effects such
as fatigue, pain, and strain. Minimize or eliminate these effects by configuring your
workstation to promote neutral or relaxed working positions.

MUSCULOSKELETAL AND REPETITIVE MOTION

HAZARD

. These hazards are caused by potential risk factors that include but are not

limited to repetitive motion, awkward posture, forceful exertion, holding static unhealthy

positions, contact pressure, and other workstation environmental factors.

To minimize musculoskeletal and repetitive motion risks:

• Use equipment that comfortably supports you in neutral working positions and

allows adequate accessibility to the keyboard, monitor, and mouse.

• Position the keyboard, mouse, and monitor to promote relaxed body and head

postures.

Safety and Electromagnetic Compatibility (EMC) Standards

This section provides information on:

•

U.S. and Canadian Safety Standards

•

Canadian EMC Standard

•

European Safety and EMC Standards

•

Australian EMC Standards

U.S. and

Canadian Safety

Standards

This instrument has been tested to and complies with standard UL 61010A-1, “Safety
Requirements for Electrical Equipment for Laboratory Use, Part 1: General Requirements”
and with standard UL 61010-2-010, “Particular Requirements for Laboratory Equipment for
the Heating of Materials.”

This instrument has been tested to and complies with standard CSA 1010.1, “Safety
Requirements for Electrical Equipment for Measurement, Control, and Laboratory Use,
Part 1: General Requirements.”

Canadian EMC

Standard

This instrument has been tested to and complies with ICES-001, Issue 3: Industrial,
Scientific, and Medical Radio Frequency Generators.

European Safety

and EMC

Standards

Safety

This instrument meets European requirements for safety (Low Voltage Directive
73/23/EEC). This instrument has been tested to and complies with standards EN 61010-
1:2001, “Safety Requirements for Electrical Equipment for Measurement, Control and
Laboratory Use, Part 1: General Requirements” and EN 61010-2-010, “Particular
Requirements for Laboratory Equipment for the Heating of Materials,” and with
standard EN 61010-2-081:2002+A1:2003 “Particular Requirements for Automatic and
Semi-Automatic Laboratory Equipment for Analysis and Other Purposes.”

«
...
23
24
25
26
27
...
»

Содержание 7300















































































































































































Отзывы:

Нет отзывов