Applied Biosystems 2720 Скачать руководство пользователя страница 72

Страница: 72 / 151

Thermal Cycler Temperature Verification System For GeneAmp

PCR Systems 2720, 9600, 9700, 9800,

and Veriti

System User Guide

Chapter 6

Calibration verification test

Calibration verification test

Use the calibration verification test to verify the temperature calibration of your
GeneAmp

PCR System 9700, Auto-Lid Sample Block Module. The verification

test consists of the following procedures, which you must perform in sequence:

Setting up the 20-µL probe assembly

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Configuring the GeneAmp

9700

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Running the test

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Evaluating the results

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PHYSICAL INJURY HAZARD.

Hot Surface. Use care when

working around the heated cover and sample block to avoid being burned by hot
components.

Required

equipment

This test requires the Dual 384-Well Sample Block Module Temperature Verification
Kit (PN 4308354), which includes:

• Light mineral oil

• Two 384-well temperature verification plates

• 20-µL probe assembly

• Digital thermometer with a 9V battery installed

Note:

This kit is also used for the Auto-Lid sample block module.

Setting up the

20-µL probe

assembly

1. Make sure the heated cover is in the rear position. If not, press and release the

red button to automatically move the heated cover to the rear position

2. Place both 384-well temperature verification plates on the sample blocks.

IMPORTANT!

The temperature verification plates must be installed in both

sample blocks throughout all temperature verification testing.

The plate labeled L1 to L6 is for the

left

sample block (

Figure 14

). The plate

labeled R1 to R6 is for the

right

sample block (

Figure 15

). Position the plates so

the angled corners face away from you.

Note:

The plates help you locate the probes within the sample blocks.

Figure 14

Left temperature

verification plate

Figure 15

Right temperature

verification plate

Содержание 2720
























































































































































Результаты поиска

Содержание 2720

Отзывы:

Бренды по названию

Популярные бренды

Applied Biosystems 2720, Руководство пользователя

Результаты поиска

Содержание 2720

Отзывы:

Бренды по названию

Популярные бренды