Apogee Instruments TS-100 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 18

Apogee Instruments TS-100 Скачать руководство пользователя страница 7

*IP55
The fan inside the TS-100 is extremely well sealed against water and dust, with an ingress protection (IP) rating of
55, called IP55. Higher numbers indicate better protection. Fans typically range from IP11 to IP55. The first digit in
the IP rating indicates protection against particle entry. A 5 indicates minimal dust entry with no interference with
fan operation. The second digit indicates water protection. A 5 indicates that water sprayed on the fan from any
direction shall have no harmful effects. Typical fans have particle and water protection ratings of 2 to 3, indicating
moderate particle and water protection, but no dust protection.

ST-110 (Precision Thermistor, not included w/ TS-100 or TS-120; included w/ TS-110 & TS-130)

TS-100/110/120/130

Difference among
Individual Replicate
Shields

Less than 0.1 C

Aspiration Rate

6 m s

-1

at full-speed; 3 m s

-1

at half-speed

Fan Input Voltage
Requirement

10.8 to 13.2 V DC

Fan Current Draw

80 mA at full-speed; 25 mA at half-speed

Fan Dust and Water
Protection

IP55*

Operating Temperature

-40 to 70 C

Dimensions

220 mm height, 270 mm diameter

Mass

840 g

Cables

5 m of shielded, twisted-pair wire for fan and air temperature sensors; TPR jacket (high water

resistance, high UV stability, flexibility in cold conditions); pigtail lead wires; stainless steel

(316), M8 connector located 25 cm from sensor head

ST-110

Measurement Range

-50 to 70 C

Measurement
Uncertainty

0.1 C (from 0 to 70 C); 0.15 C (from -35 to 0 C)

Measurement
Repeatability

less than 0.01 C

Non-stability
(Long-term Drift)

less than 0.02 C per year (when used in non-condensing environments where the annual

average temperature is less than 30 C; continuously high temperatures or continuously humid

environments increase drift rate)

Equilibration Time

5 s

Self-Heating

less than 0.01 C (typical, assuming pulsed excitation of 2.5 V DC); 0.08 C at 5 C (maximum,

assuming continuous input excitation of 2.5 V DC

Operating Environment

-50 to 70 C; 0 to 100 % relative humidity

Input Voltage
Requirement

2.5 V DC excitation (recommended, see (OPERATION AND MEASUREMENT section)

Output Voltage Range

0 to 2.5 VDC (assuming continuous input excitation of 2.5 V DC)

Current Drain

0.1 mA DC at 70 C (maximum, assuming continuous input excitation of 2.5 V DC)

Dimension

70 mm length; 2 mm diameter

Mass

60 g

«
...
5
6
7
8
9
...
»

Содержание TS-100



















Отзывы:

Нет отзывов