background image

 

12 

 

 

DUAL POINT LOCK RELASE  

 

Figure 5 

 

FINAL ASSEMBLY  

 

Check all bolts and nuts to make sure they are tight. Do not use an impact gun on concrete Anchors.  

 

Check all fittings or leaks. If necessary, make sure the arm lock restraints are engaging properly and smoothly. If 

not, tap the main lock forward or backward as needed with a rubber mallet to insure proper engagement on all 4 gears with 

the arm restraint locks.  

 

Cycle lift up and down to insure carriages are synchronized. 

 

Place a vehicle on the lift and raise until swivel pads are contact with frame of the vehicle. Raise the vehicle about 

3 feet and lower until the tires touch the floor. Keep raising and lowing the vehicle. Increase the height each time until the 

vehicle is completely to top. This procedure pumps all the air from the system.  

TESTING AND ADJUSTING LIFT 

 

With the power properly hooked up and hydraulic oil in the Pump Reservoir, push the Push Button on the side of 

the Motor to raise the Carriages off the locks. Release the Push Button and then pull the Lock Release Cable under each 

carriage to release the locks. Run the lift all the way up and down two more times to bleed all the air from the system.  

 

While running the lift, listen to safeties clicking. Each side should click simultaneously or with-in a 1/2 second of 

each other. If they are not clicking together, then adjust the cables to compensate by tightening the side opposite the one 

that is clicking last at the cable bolt at the top of the carriage on the same side.  

 

Remember not to over tighten cables 

 they should be firm, much like a banjo string or a fan belt in a car. 

 

Now the lift is ready for use.  

 

 

 

Содержание HW-9KBP


















Отзывы: