Aplisens 0005 0004 0006 0000 0000 0002 0001 72 Скачать руководство пользователя страница 6

Страница: 6 / 35

EN.IO.APC.APR.ALW

Revision 02.A.005/2020.06

TABLE OF CONTENTS

INTRODUCTION .......................................................................................... 8

1.1.

Purpose of the document ............................................................................................ 8

1.2.

Trademarks ................................................................................................................. 8

1.3.

Definitions and abbreviations ...................................................................................... 9

1.4.

Transmitter set range ................................................................................................ 10

SAFETY ..................................................................................................... 11

TRANSPORT AND STORAGE .................................................................. 12

3.1.

Delivery check ........................................................................................................... 12

3.2.

Transport ................................................................................................................... 12

3.3.

Storage...................................................................................................................... 12

GUARANTEE ............................................................................................ 12

IDENTIFICATION ....................................................................................... 13

5.1.

Manufacturer’s address ............................................................................................. 13

5.2.

Transmitter identification ........................................................................................... 13

5.3.

CE mark, declaration of conformity ........................................................................... 13

INSTALLATION ......................................................................................... 14

6.1.

General recommendations ........................................................................................ 14

6.1.1.

Examples of transmitter installation .................................................................... 14

6.1.2.

Installation instructions for transmitters with distance separators ....................... 15

ELECTRICAL CONNECTION .................................................................... 16

7.1.

Cable connection to transmitter internal terminals .................................................... 16

7.1.1.

Cable connection ............................................................................................... 16

7.1.2.

Connection of transmitter with the option of using local HART communication.. 17

7.2.

Transmitter power supply .......................................................................................... 19

7.2.1.

Transmitter supply voltage ................................................................................. 19

7.2.2.

Uninterruptible current measurement in 4…20 mA current loop ........................ 19

7.2.3.

Specifications of electrical switching terminals ................................................... 19

7.2.4.

Cabling specification .......................................................................................... 19

7.2.5.

Resistance load in power supply line ................................................................. 19

7.2.6.

Shielding, equipotential bonding ........................................................................ 20

7.3.

Equipotential bonding ................................................................................................ 20

7.4.

Overvoltage protection .............................................................................................. 20

7.5.

Final inspection of cabling ......................................................................................... 20

OPERATION .............................................................................................. 21

8.1.

Local buttons ............................................................................................................. 25

8.2.

Local configuration of setpoints ................................................................................. 25

8.3.

Navigation in local setpoints MENU .......................................................................... 25

8.4.

Acceptance of local setpoints .................................................................................... 25

8.5.

Structure of local setpoints MENU ............................................................................ 26

8.6.

Remote configuration of setpoints (HART 5/HART 7) ............................................... 27

8.6.1.

Compatible devices ............................................................................................ 27

8.6.2.

Compatible configuration software ..................................................................... 27

8.6.3.

Local HART communication jumper ................................................................... 27

START-UP ................................................................................................. 28

Содержание 0005 0004 0006 0000 0000 0002 0001 72




































Результаты поиска

Содержание 0005 0004 0006 0000 0000 0002 0001 72

Отзывы:

Похожие инструкции для 0005 0004 0006 0000 0000 0002 0001 72

Бренды по названию

Популярные бренды

Aplisens 0005 0004 0006 0000 0000 0002 0001 72, Руководство пользователя

Результаты поиска

Содержание 0005 0004 0006 0000 0000 0002 0001 72

Отзывы:

Похожие инструкции для 0005 0004 0006 0000 0000 0002 0001 72

Бренды по названию

Популярные бренды