Aplex ARCHMI-932P Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 121

Aplex ARCHMI-932P Скачать руководство пользователя страница 15

ARCHMI-932P User Manual

13

Chapter 2 Hardware

2.1 Motherboard Specifications

Specifications

System

Processor

6th Generation Intel® CoreTM Processors, BGA 1356
Intel® CoreTM i7-6600U Processor, Dual Core, 4M Cache, 2.6GHz (3.4GHz), 15W
Intel® CoreTM i5-6300U Processor, Dual Core, 3M Cache, 2.4GHz (3.0GHz), 15W
Intel® CoreTM i3-6100U Processor, Dual Core, 3M Cache, 2.3GHz, 15W
Intel® Celeron® Processor 3955U, Dual Core, 2M Cache, 2.0GHz, 15W

Memory

Two 204-pin SODIMM up to 16GB

Dual Channel DDR3L 1600MHz

BIOS

Insyde SPI 128Mbit

Graphics

Controller

Intel® HD Graphics GT Series

Features

OpenGL 5.0, DirectX 12, OpenCL 2.1
HW Decode: AVC/H.264, MPEG2, VC1/WMV9, JPEG/MJPEG, HEVC/

H265, VP8, VP9

HW Encode: AVC/H.264, MPEG2, JPEG, HEVC/H265, VP8, VP9

Display

1 x LVDS/eDP (eDP available upon request)

1 x HDMI/DP (DP available upon request)

1 x DP++

LVDS: dual channel 48-bit, resolution up to 1920x1200 @ 60Hz

DP: resolution up to 4096x2304 @ 60Hz
HDMI: resolution up to 2560x1600 @ 60Hz or 4096x2160 @ 24Hz

Triple
Displays

LVDS + HDMI + DP++
LVDS + DP + DP++ (available upon request)

eDP + HDMI + DP++ (available upon request)
eDP + DP + DP ++ (available upon request)

Expansion

Interface

1 x PCIe x4 (Gen 3)

1 x SIM

1 x Full-size Mini PCIe (PCIe/USB/SATA)
1 x Full-size Mini PCIe (PCIe/USB)

Audio

Audio Codec Realtek ALC888S-VD2-GR

Ethernet

Controller

1 x Intel® I210AT PCIe (10/100/1000Mbps)

1 x Intel® I219LM PCIe with iAMT11.0 (10/100/1000Mbps) -

(only Core i7/i5 supports iAMT)

Rear I/O

Ethernet

2 x GbE (RJ-45)

«
...
13
14
15
16
17
...
»

Содержание ARCHMI-932P


























































































































Отзывы:

Нет отзывов