Apex Digital MASS FLOW METER Скачать руководство пользователя страница 8

Страница: 8 / 46

Getting Started

The Flow Meter Display

The figure below identifies the various features of the flow meter display.

Press the bottom central button to toggle the backlight on and off.

Engineering units

are used by the meter in its serial communications and

calculations. These can be different from

button units

, which are the units

being displayed. These are independently configurable. See

page 18



Highlights

pressure

in the center of the meter. Push a second

time to choose the pressure parameter (if available), or to select

pressure engineering units.



Highlights

temperature

Push a second time to select

temperature engineering units.



TARE FLOW

tare the flow

rate

(see

page 20



Highlights

volumetric (actual)

flow

rate. Push a second

time to select volumetric flow

rate engineering units.



Highlights

mass flow

rate. Push a

second time to select a different

mass flow (normal mass flow) or

true mass flow engineering unit.



TOTAL/MENU

Accesses the optional

flow totalizer

(

page 19

enters the Menu system (

page 20

)



Toggles the backlight.

Status Messages

Status messages are shown to the right of the main readout number, in

the example above as

OVR

ADC

Analog-digital converter error

LCK

Front display is locked

OVR

Totalizer rolled over to zero

POV

Pressure over range of device

MOV

Mass flow over range of device

TMF

Totalizer missed out of range flow

TOV

Temperature over range of device

VOV

Volumetric flow over range of device













PSIA

¤C

TARE

+13.60 +24.38 FLOW

+24.38

Flow Temp

¤C

Air

OVR

+16.670 +15.440

LPM

SLPM

The Flow Meter Display



Содержание MASS FLOW METER















































Результаты поиска

Содержание MASS FLOW METER

Отзывы:

Похожие инструкции для MASS FLOW METER

Бренды по названию

Популярные бренды

Apex Digital MASS FLOW METER, Руководство по эксплуатации

Результаты поиска

Содержание MASS FLOW METER

Отзывы:

Похожие инструкции для MASS FLOW METER

Бренды по названию

Популярные бренды