Apex Digital MASS FLOW METER Скачать руководство пользователя страница 18

Страница: 18 / 46

Navigation and Customization

Choosing Engineering Units

Press the button adjacent to any of the four

measurement parameters twice to enter its

unit selection menu. You can change units in

two ways:

Button engineering units

(

page 18

) alter

the display only, not the serial data:

•

Select

Set button eng units

and

press

SELECT

to change the engineering

unit on the display only. This does

not alter the flow meter data frame.

Device engineering units

alter both the display and the flow meter data frame:

•

Select

Set device eng units

and then choose the

engineering unit as above. An additional confirmation

screen asks you to confirm the serial change.

•

If the button engineering unit is different than the device engineering

unit,

Set device eng units

will not appear. To change them:

•

First select

Show device eng units

to revert the button to the

current device unit for that parameter. Enter the unit selection

menu again to change the device engineering unit.

✓

Note:

The totalizer's set flow variable (mass flow or

volumetric flow) cannot be altered directly. Please

contact support (

page 2

) if you wish to change your

totalizer from mass flow to volumetric, or vice-versa.

Changing the engineering units:

DOWN

>Show abs pressure

Show gauge pressure
Show baro pressure
Set button eng units
Set device eng units

CANCEL

SELECT

Engineering Unit Screen









PSIA

¤F

TARE

+13.68 +75.88 FLOW

+75.88

Flow Temp

¤F

Air

+0.0000 +0.0000

LPM

SLPM MENU

DOWN

Set button eng

units

>Show device eng

units

BACK

SELECT

PSIA

¤C

TARE

+13.68 +24.38 FLOW

+24.38

Flow Temp

¤C

Air

+0.0000 +0.0000

LPM

SLPM MENU

DOWN

Set button eng units

>Set device eng units

BACK

SELECT

Содержание MASS FLOW METER















































Результаты поиска

Содержание MASS FLOW METER

Отзывы:

Похожие инструкции для MASS FLOW METER

Бренды по названию

Популярные бренды

Apex Digital MASS FLOW METER, Руководство по эксплуатации

Результаты поиска

Содержание MASS FLOW METER

Отзывы:

Похожие инструкции для MASS FLOW METER

Бренды по названию

Популярные бренды