Apevia X-Qpack2, Руководство пользователя

Страница: 2 / 13

USER'S MANUAL
2
3
4
1.3 Remove screws as shown
to access the motherboard
tray.
1.5 If your motherboard
included an I/O shield, then
replace the X-QPACK2 I/O
shield with it. Remove shield
by pushing it inward from
the position shown.
1.6 Place motherboard on the
tray standoffs and screw
into place.
1.4 Slide the motherboard tray
out of the case.
1.7 Remove covers of expansion
slots that you need and install
any expansion cards that you
have.
1.15 Place 5 1/4" drive(s) into the
drive bay.
1.14 Remove 5 1/4" drive bay
cover(s) by pushing it out
from behind.
1.13 Place a screwdriver in the
hole and lift metal plate.
Then wiggle plate up/down
until it comes loose.
1.12 Secure hard drive by fasten-
ing screws on both sides of
the cage.
1.11 Slide hard drive into cage.
1.10 Slide cage upward to remove.
1.8 Replace the motherboard tray
into the chassis.
1.9 Remove screws to release
the hard drive cage.
1.17 Replace the hard drive cage
and fasten screws.
All screws for M/B, DVD, HDD are provided inside of the chassis.
Finished appearance.
1
5
6
7
1. Install motherboard, 3 1/2", and 5 1/4" drives:
8
1.1 Remove thumbscrews
from the rear of the
X-QPACK2. 1.2 Remove the 3-sided panel
by sliding it back then
lifting upward.
4. Install Hard Drive and CPU temperature sensors:
3. Install front panel leads and LEDs:
5. USB/1394(Firewire)/Audio cable pin assignment:
9
CONTENTS
1. Install motherboard, 3 1/2", and 5 1/4" drives........1
2. Identify the power supply connectors.....................6
3. Install front panel leads and LEDs.........................7
4. Install Hard Drive and CPU temperature sensors.....7
5. USB/1394(Firewire)/Audio cable pin assignment......8
2.4 Serial ATA (SATA) connector
x 2. These provide power
to your
SATA devices.
2.3 4pin peripheral connector x 6.
These provide power for
IDE
devices (HD, CD/DVD) and
case fans.
1.16 Secure 5 1/4" drive by
fastening screws on both
sides of the drive bay.
2. Identify the power supply connectors:
2.5 6pin PCI Express connector x 1.
This connector provides power
to your PCI Express devices.
2.6 Floppy drive connector x 2.
Use to power 3 1/2" floppy
drives.
3.1 Locate the USB/Audio/1394
(Firewire) front panel connect-
ors. Refer to your mother-
boards manual for the proper
pin assignment. Generally there
is a small triangle on the conn-
ectors to indicate the positive
line.
'
4.1 Locate HD/CPU senors.
4.3 Tape sensor to the
CPU heatsink to
monitor CPU temperature.
6. Complete the Installation.....................................9
6. Complete the Installation:
2.2 ATX 12V P4 connector x 1.
Supplies power to the
CPU via the motherboard.
(see your motherboards manual for location of USB/Firewire
headers.)
'
2.1 20/24 pin ATX connector x 1.
Four pins can be detached by
gently pulling them if you need
20pin.
Note: You may also leave the
sensor loose in the chassis
in order to monitor overall
system temperature.
DO NOT place the sensor
directly on the CPU as it
may cause system damage.
4.2 Tape sensor to hard
drive to monitor its
temperature.
3.2 Locate the Power LED,
HDD LED, Power SW,
Reset SW and Speaker
front panel leads.
Again, please refer to
your motherboards'
manual for the proper
pin assignment.
6.1 Once all components have been installed properly, gently
return the 3-sided panel to its initial position (lower the panel
over the chassis and push forward). Congratulations, you
have completed the assembly of your X-QPACK2.
Cable Cable Color Function
RED +5V
WHITE -D
GREEN +D
BLACK GND
WHITE VP
BLACK VG
RED TPB-
GREEN TPB+
BROWN TPA-
BLUE TPA+
RED MIC-IN
BLACK GND
WHITE MIC-POWER
GREEN LINE OUT FR
BROWN LINE OUT RR
YELLOW LINE OUT FL
BLUE LINE OUT RL
USB 2.0
1394
AUDIO