background image

Instruction manual

REVAMP4240T

5

15.   Do not install near any heat sources such as radiators, heat registers, 

stoves, or other apparatus (including amplifiers) that produce heat.

16.   Do not defeat the safety purpose of the polarised or grounding plug.  

A polarised plug has two blades with one wider than the other. A 
grounding plug has two blades and a third grounding prong. The wide 
blade or the third prong is provided for your safety. Always use the 
device with a grounded mains power plug. If the provided plug does not 
fit into your outlet, consult an electrician for replacement of the obsolete 
outlet.

17.   Protect the power cord from being walked on, pinched or damaged. 

Particularly at the plugs, connectors and at the point where they exit 
from the apparatus.

18.   Only use attachments/accessories specified by the manufacturer.

19.   Unplug the apparatus during lightning storms or when unused for long 

periods of time.

20.   Use only with the cart, stand, tripod, bracket, or 

table specified by the manufacturer, or sold with the 
apparatus. When a cart or rack is used, use caution 
when moving the cart/apparatus combination to avoid 
injury from tip-over.

21.   Refer all servicing to qualified personnel. Servicing is required when the 

apparatus has been damaged in any way, such as power supply cord 
or plug is damaged, liquid has been spilled or objects have fallen into 
the apparatus has been exposed to rain or moisture, does not operate 
normally, or has been dropped. 

22.   WARNING: To reduce the risk of fire or electric shock, do not expose this 

apparatus to rain or moisture. The apparatus shall not be exposed to 
dripping or splashing and that objects filled with liquids, such as vases, 
shall not be placed on apparatus. 

23.   WARNING: The mains plug/appliance coupler is used as disconnect 

device, the disconnect device shall remain readily operable.  
 
 
 

Содержание REVAMP4240T

















Отзывы: