AP Diving APV200 Скачать руководство пользователя страница 29

Страница: 29 / 30

AP Diving Ltd. APV200 Inflator Maintenance Manual

Page 29 of 30

6.18 Put spring onto snap connector body

- Again: make sure you do not lose one of the 4 ball bearings during this step.

6.19 Push sliding collar onto snap connector body

- The collar can only go on in one way. Push it on with the wider opening facing the

hose, and the smaller opening facing the circlip, to be fitted in the next step.

- Again: make sure you do not lose one of the ball bearings during this step.

6.20 Refit circlip onto snap connector body

- Before fitting it back on, make sure it hasn’t been stretched and become too wide

during removal. If unsure: use a new circlip.

WARNING

: If that is the case, it may come inadvertently off again during use,

rendering the whole hose connection and anything it is attached to inoperable!

- Just push it back on. Check that you can rotate it in its groove after fitting. It should

rotate, but only with slight difficulty. If it rotates too easily, it may have become too
wide. In that case remove it, tighten it up and refit it – or fit a new one.

This completes the re-assembly of the AP50 Medium Pressure hose.

Содержание APV200































Результаты поиска

Содержание APV200

Отзывы:

Бренды по названию

Популярные бренды

AP Diving APV200, Руководство по обслуживанию

Результаты поиска

Содержание APV200

Отзывы:

Бренды по названию

Популярные бренды