background image

12 

BASIC TROUBLESHOOTING GUIDE 

PROBLEM 1: THE UNIT HAS NO POWER 

1.  Check if the unit is switched ON. 

2.  Check the fuse. Replace with the same type if fuse is blown. 

3.  Check the power cord and ensure there are no disconnections. 

4.  Verify that the unit is properly connected to the power source.

 

PROBLEM 2: PANEL DISPLAYS “Err” MESSAGES 

DESCRIPTION: 

Display show

 “SEnS” “Err” 

messages. \

 

ERR0  — First external temperature probe not detected 

ERR1  — Second external temperature probe not detected 

ERR2  — Internal  temperature probe not detected 

ERR3  — First external temperature probe not  attached. 

SOLUTION: 

Turn off power and back on. 

If  err  messages  shows  err0  or  err1  check  the  connection  of  sensor  to  its 

receptacle. Check if the temperature probe tip is still intact. 

If err messages  shows  err2 internal temperature connector might have come 

loose or needs to be replaced. 

If  err  messages  shows  err3,  the  first  external  temperature  probe  was  not 

detected, secure the external temperature on the underside of the board to be 

worked on.

 

PROBLEM 3: DISPLAY AND OTHER DEVICE OPERATION 

ISSUES 

SOLUTION: 

Turn off power and back on.

 

OTHER PROBLEMS NOT MENTIONED: 

Contact the vendor.

 

IR­Preheating System

 

Int883 

INSTRUCTION MANUAL 

Thank you for purchasing Aoyue Int883 IR­Preheating System. 

It is important to read the manual before using the equipment. 

Please keep manual in accessible place for future reference.

 

This  manual  is  designed  to  familiarize  the  technician  with 
the  proper  operation  and  maintenance  of  the  equipment. 
The  “Care  and  Safety  Precautions”  section  explains  the 
hazards of using any type of soldering or reworking device. 
Please read carefully and observe the guidelines in order to 
maximize usage and minimize the risk of injury or accidents .

Содержание INT883







Отзывы: