background image

12  

!

 

BASIC TROUBLESHOOTING GUIDE 

PROBLEM 1: THE UNIT HAS NO POWER 

1.  Check if the unit is switched ON. 
2.  Check the fuse. Replace with the same type if fuse is blown. 
3.  Check the power cord and ensure there are no disconnections. 
4.  Verify that the unit is properly connected to the power source. 

 
PROBLEM 2: PANEL DISPLAYS “Err” MESSAGES 
DESCRIPTION: 

Display show 

“SEnS” “Err”

 messages. \ 

 
ERR0  — First external temperature probe not detected

 

ERR1  — Second external temperature probe not detected 
ERR2  — Internal  temperature probe not detected 
ERR3  — First external temperature probe not  attached. 

 
SOLUTION: 

Turn off power and back on.  

If  err  messages  shows  err0  or  err1  check  the  connection  of  sensor  to  its 
receptacle. Check if the temperature probe tip is still intact. 
 
If err messages shows err2 internal temperature connector might have come 
loose or needs to be replaced. 
 
If  err  messages  shows  err3,  the  first  external  temperature  probe  was  not 
detected, secure the external temperature on the underside of the board to be 
worked on. 
 

PROBLEM 3: DISPLAY AND OTHER DEVICE OPERATION 
ISSUES 
SOLUTION: 

Turn off power and back on.  

 

OTHER PROBLEMS NOT MENTIONED: 

Contact the vendor. 

 

   

!

IR-Preheating System

!

Int863

!

INSTRUCTION MANUAL

!

Thank you for purchasing Aoyue Int863 IR-Preheating System. 

It is important to read the manual before using the equipment. 

Please keep manual in accessible place for future reference. 

This  manual  is  designed  to  familiarize  the  technician  with 

the proper operation and maintenance of the equipment. 
The  “Care  and  Safety  Precautions”  section  explains  the 

hazards of using any type of soldering or reworking device. 

Please read carefully and observe the guidelines in order to 

Содержание Int863







Отзывы: