Aosenma CG035 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 29

background image

SWC:

The outer button (furthest right).

Binding. (Aka ‘Internal fequency’)

Normally only used in the factory as this involves
disassembling the quadcopter to access the binding
button inside the chassis on the receiver/transmitter
board there.
I have never personally had to do this but from reports it
is accomplished by holding down the bind button inside
the quadcopter then inserting the battery and then
pressing the Binding button on the controller while
switching it on. Procedure in troubleshooting later.

The inner button.

Follow me mode.

The drone is supposed to point towards and follow the controller with no guidance from
you, however you can still alter its height and distance from you using the controls while in
this mode. Again, you may experience 'variable' results with this such as it pointing in the
wrong direction.

SWD:

These are both camera controls for use with the factory
First Person View camera and alleged 'gimbal'.

Inner button

Starts and stops on board video recording, one press to
start, a further press to stop.

Outer button

(furthest left)

Takes a photo. You cannot take a photo while continuing
to record video. If you press the photo button it
immediately stops video recording.

Gimbal control:

This button is to the left of the Auto takeoff button, and is used
to control the pitch and roll of the camera. Slowly, unreliably
and overall, Badly.

«
...
7
8
9
10
11
...
»

Содержание CG035






























Отзывы:

Нет отзывов

Похожие инструкции для CG035

zoopa q cruiser 420

Бренд: ACME Страницы: 42

Бренд: dji Страницы: 60

Бренд: Quad Monsters Страницы: 13

Бренд: YUNEEC Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды