1.
Pull up the CPU socket lever and up to
90-degree angle.
2.
Locate Pin 1 in the socket and look for a
(golden) cut edge on the CPU upper interface.
Match Pin 1 and cut edge. Then insert the
CPU into the socket.
3.
Press down the CPU socket lever and finish
CPU installation.
Plug in the CPU fan cable to the 3-pin
CPU FAN
connector. If you have chassis fan,
you can also plug it on
System FAN
or
AUX FAN
(without H/W monitoring)
connector.
CPU Ratio
3x, 3.5x, 4x, 4.5x, 5x, 5.5x, 6x, 6.5x, 7x, 7.5x, 8x, 8.5x, 9x, 9.5x, 10x, 10.5x, 11x,
11.5x, and 12x
CPU FSB (By BIOS table)
66.6, 66.8, 68.3, 70, 75, 80, 83, 100, 100.2, 103, 105, 110, 115, 120, 124, 133.3,
133.6, 137, 140, 145, 150, 160, 166.5 and 200 MHz
CPU FSB (By manual
Adjustment)
FSB = 66, 66~83MHz
FSB = 100, 75~124MHz
FSB = 133, 100~248MHz
CPU
CPU Core Frequency
FSB Clock
Ratio
Celeron 533
533MHz
66MHz
8x
Celeron 566
566MHz
66MHz
8.5x
Celeron 600
600MHz
66MHz
9x
Celeron 766
766MHz
66MHz
11.5x
Celeron 800
800MHz
100MHz
8x
Celeron 850
850MHz
100MHz
8.5x
Celeron 900
900MHz
100MHz
9x
Celeron 1.2G
1.2GHz
100MHz
12x
Pentium III 600E
600MHz
100MHz
6x
Pentium III 650E
650MHz
100MHz
6.5x
Pentium III 700E
700MHz
100MHz
7x
Pentium III 750E
750MHz
100MHz
7.5
Pentium III 800E
800MHz
100MHz
8x
Pentium III 850E
850MHz
100MHz
8.5x
Pentium III 533EB
533MHz
133MHz
4x
Pentium III 600EB
600MHz
133MHz
4.5x
Pentium III 667EB
667MHz
133MHz
5x
Pentium III 733EB
733MHz
133MHz
5.5
Pentium III 800EB
800MHz
133MHz
6x
Pentium III 866EB
866MHz
133MHz
6.5
Pentium III 933EB
933MHz
133MHz
7x
Pentium III 1G
1GHz
133MHz
7.5x
Pentium III 1.13G
1.13GHz
133MHz
8.5x
Warning:
To avoid possible CPU damage caused by overheating, an automatic shutdown of
system had been especially designed on this motherboard. System would be automatically
power off when this motherboard with implementation of THERMTRIP circuit detected a
CPU temperature above 135 degree for 4 seconds.
5. Setting CPU Voltage & Frequency
Note:
If you do not match the CPU
socket Pin 1 and CPU cut edge well, it
may damage the CPU.
CPU Pin 1 and cut edge
Setting CPU Core Voltage
This motherboard supports CPU VID function. The CPU core voltage will be automatically
detected and the range is from 1.05V to 1.825V. It is not necessary to set CPU Core
Voltage
Setting CPU Frequency
This motherboard is CPU jumper-less design, you can set CPU frequency through the
BIOS setup, and no jumpers or switches are needed.
BIOS Setup > Frequency / Voltage Control > CPU Speed Setup
FAN2 Connector
This socket supports FC-PGA/FCPGA2 package CPU, which is the latest CPU package
developed by Intel, we strongly recommend you not to insert former PPGA-package CPU
onto it.
4. Installing CPU & Housing Fan
3. Installing Processor
CPU socket lever
Note:
Some CPU fans do not have
sensor pin, so that cannot support fan
monitoring.
FAN3 Connector
Warning:
Intel
®
815E B-Step
chipset supports maximum
133MHz FSB and 66MHz AGP
clock, higher clock setting may
cause serious system damage.
CPU Fan Connector
Tip:
If your system hangs or
fails to boot because of
overclocking, simply use
<Home> key to restore the
default setting or you can wait
the AOpen “Watch Dog
Timer” reset the system in
five seconds and system will
auto-detect hardware again.
GND
+12V
SENSOR
GND
+12V
SENSOR
