AOpen AK86-L, Простое руководство по установке

Страница: 4 / 8

8. Connecting Front Panel Cable
Attach the power LED, speaker, and reset switch connectors
to the corresponding pins. If you enable “Suspend Mode”
item in BIOS Setup, the ACPI & Power LED will keep
flashing while the system is in suspend mode.
Locate the power switch cable from your ATX housing. It is
2-pin female connector from the housing front panel. Plug
this connector to the soft-power switch connector marked
SPWR .
7. Connecting IDE, Floppy Cables
Pin 1
ATA 66/100/133
IDE Connector
FDD Connector
Connect 34-pin floppy cable and 40-pin IDE cable to floppy connector FDD connector. Be
careful of the pin1 orientation. Wrong orientation may cause system damage.
IDE 2 (Secondary)
IDE 1 (Primary)
Pin 1
6. Installing Memory Modules
ATA 66/100/133
1
SPEAKER
IDE LED
Power Switch
ACPI & Power LED
RESET
SPWR
GND
ACPILED-
GND
NC
NC
GND
RESET
GND
NC
NC
+5V
IDE LED
IDE LED
+5V
+5V
GND
NC
SPEAKER
1
This motherboard has three 184-pin DDR DIMM sockets that allow you to install
DDR266/333 memory up to 3 GB and DDR400 memory up to 2GB. Non-ECC DDR RAM is
supported. Otherwise, it will cause serious damage on memory sockets or RAM module.
Please follow the table below to install RAM modules. Newly implemented function, the
Voltage of memory on this motherboard is adjustable from 2.5V to 2.7V for over clocking
purpose.
DIMM 1
DIMM 2
DIMM 3
Number
of DIMMs
DIMM 1 DIMM 2 DIMM 3 Max Speed
1 X8 or X16 single bank empty empty DDR400
1 empty X8 or X16 single bank empty DDR400
1 empty empty X8 or X16 single bank DDR400
1 X8 double bank empty empty DDR400
1 empty X8 double bank empty DDR400
1 empty empty X8 double bank DDR400
2 X8 or X16 single bank X8 or X16 single bank empty DDR400
2 X8 or X16 single bank X8 double bank empty DDR400
2 X8 or X16 single bank empty X8 or X16 single bank DDR400
2 X8 or X16 single bank empty X8 double bank DDR400
2 X8 double bank X8 or X16 single bank empty DDR400
2 X8 double bank X8 double bank empty DDR400
2 X8 double bank empty X8 or X16 single bank DDR400
2 empty X8 or X16 single bank X8 or X16 single bank DDR333
2 empty X8 or X16 single bank X8 double bank DDR266
2 empty X8 double bank X8 or X16 single bank DDR266
2 empty X8 double bank X8 double bank DDR266
2 X8 double bank empty X8 double bank DDR400
3 X8 or X16 single bank X8 or X16 single bank X8 or X16 single bank DDR333
3 X8 or X16 single bank X8 or X16 single bank X8 double bank DDR266
3 X8 or X16 single bank X8 double bank X8 or X16 single bank DDR266
3 X8 or X16 single bank X8 double bank X8 double bank DDR266
3 X8 double bank X8 or X16 single bank X8 or X16 single bank DDR333
3 X8 double bank X8 or X16 single bank X8 double bank DDR266
3 X8 double bank X8 double bank X8 or X16 single bank DDR266
3 X8 double bank X8 double bank X8 double bank DDR266
Tip: “X8” means that each chip on the module
bank is 8 bits, and “X16” means each chip is 16
bits. We know that each memory bank is 64 bits.
Therefore, if a memory module has 8 chips on
each bank it is “X8”, and if there are 4 chips on
each bank, it is “X16”.
Note: Due to the limitation of memory controller in the Athlon 64 CPU,
we do not recommend you to install three DDR333/266 modules.