Anzzi SD-AZ03-01 Скачать руководство пользователя

Страница: 6 / 10

Place the

Stationary glass panel (01)

and

Return

glass panel (03)

back into the designated position,

assemble the

Wall brackets (14)

and tighten the bolts.

See Fig. 5 for details.

Fig

. 5

Locate the

Support bar (04)

Adjust the bar to a proper position on the glass
and the wall. Level it horizontally. Hold it firmly and

outline the bracket’s position on the wall. Remove
the

Support bar

and detach the wall bracket from

it. Place the wall bracket against its outlined

position on the wall and mark the drilling hole.
Drill the hole using

Ø 5/16”

drill bit, insert the

Wall anchor (07)

and fasten the wall bracket to

the wall with the

Big head Screw ST4.2×55 (09)

Attach the

Support bar

to the wall as shown on

Fig. 6.5 and tighten the set screws and the glass
holding screw to secure the glass.

See Fig. 6 and Fig. 7 for details.

Fig

. 6

Ø 5/16”

Содержание SD-AZ03-01











Результаты поиска

Содержание SD-AZ03-01

Отзывы:

Похожие инструкции для SD-AZ03-01

Бренды по названию

Популярные бренды

Anzzi SD-AZ03-01, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SD-AZ03-01

Отзывы:

Похожие инструкции для SD-AZ03-01

Бренды по названию

Популярные бренды