Anywave ATSC 140W Скачать руководство пользователя страница 7

 

                     

    ATSC 140W TX Quick Start Guide 

 

ACT-140-QSG-DOC-V1.3, 09/29/2014 

 

Page 7 of 13 

 

 

 

3

 

TX System Overview 

 
Final assembly and test of each transmitter is performed at the Anywave factory. 

The  Exciter  is  setup  on the  desired  channel  frequency  and  the TX  is  tested  with  the 
complete  RF  system  (if  purchased)  at  full  power  into  a  load.  All  TX  operating 
parameters are optimized and the Transmitter Forward and Reflected power meters are 
properly calibrated. Linear and Nonlinear precorrection is performed and automatically 
stored in non-volatile memory inside the Exciter. A Factory Test Report is completed 
for each system, providing a record of full power operating parameters and performance. 
The TX then goes through a final 24-hour burn-in period and check out before being 
shut done and packed up for shipment.   

 
In your shipment, you should receive a copy of the following documentation. 
 
- Packing Checklist   
- Transmitter Factory Test Report 
- 140W TX Quick Start Guide 
- 140W PA and Exciter User Manuals   
 

Carefully unpack  and inspect  all  your  equipment  and please review the Packing 

Checklist when you receive your system to be certain you have received all your system 
components.  Also,  please  be  sure  to  identify  and  remove  all  packing  materials  and 
supports (foam pads, etc.) prior to initial turn on of the equipment. 

 
All Single PA TX systems ship with an AC power cord included with the Exciter 

and  PA.  The  PA  shipment  also  includes  an  RS232  cable,  for  Exciter  to  PA 
communications, and a CAT5 Ethernet cable, for Exciter to PC built-in web interface 
Remote Monitoring and Control. 
 

 

 

Содержание ATSC 140W














Отзывы: