DELUXE FOOD WARMER
12
P/N 1010678 Rev. F 09/04
DELUXE FOOD WARMER
13
P/N 1010678 Rev. F 09/04
OPERATION (continued)
WARNING
To avoid injury, be careful when opening top
cover. Be sure to allow steam to escape before
putting hands or face over the steamer.
Programming - Timer Models
CYC (Total Cycle Time
) refers to the total amount of
steaming time set for the product.
SHO (Shot Interval Time)
is the time set between
shots of steam during a complete cycle.
H2O Setting (Steam Shot Time)
is used to adjust the
water volume used during each pump/solenoid opera-
tion.
The amount of steam produced by your Deluxe Food
Warmer (steamer) depends on the amount of water
sprayed onto the steam generator.
Flooding of the generator may occur if the H2O setting
is set too high. To prevent this from occurring, the Shot
Interval Time (SHO) may be increased to allow more
time for generator heat recovery. Adjustments should
be made to both values to determine the optimum set-
tings for your cooking needs.
To program the control, refer to Figure 7 and use the
following procedure in sequence:
1. Turn the Rocker Switch (power On/Off) to ON.
The display shows the factory programmed Total
Cycle Time in minutes and seconds (Item A,
Figure 7).
2. Press and release the Program button to change
the control from OPERATION to PROGRAM
mode.
3. To change the Total Cycle Time in minutes, use
the UP or DOWN arrow buttons to change the
time (Item B, Figure 7).
4. Press and release the Program button again and
use the UP or DOWN arrow buttons to change the
Total Cycle Time in seconds (Item C, Figure 7).
5. To change the SHO factory settings, make sure
the control is in PROGRAM model, then press
and hold the two arrow buttons simultaneously for
1-2 seconds and then release. SHO will be dis-
played (Item D, Figure 7).
6. Press and release the Program button and use
the UP or DOWN arrow buttons to change the
SHO setting in seconds (Item E, Figure 7).
NOTE: 20 seconds is recommended.
�����
Figure 6. Operating Controls Non-Timer Models
Rocker Switch
(Power On/Off)
Operate
Button
Operating Instructions For Timer Models
1. Turn the Rocker Switch (power On/Off) to ON
(Figure 6).
2. Allow the unit to preheat for approximately 30
minutes.
IMPORTANT: The flashing green ready light will
become steady when the unit is up to temperature
and ready to be used.
IMPORTANT: Do not push the operate button dur-
ing warm-up. The flashing green light indicates
unit is not up to temperature.
3. Open the top cover and place the product to be
steamed onto the trivet, then close the cover.
4. Single Shot: Press the operate button for 1 sec-
ond then release and wait 20 seconds for the
steam to penetrate the product.
Timed Cycle: Press the start/stop button to begin
the steaming cycle. Display will count down to
zero.
5. Remove steamed product.
6. See the Steaming Guide section of this manual.
Содержание Roundup 9100101
