On/Off
Power
Switch
Red Power LED
3
2
INTRODUCTION
Your Digital TV Signal Meter helps you align your aerial for the best digital reception
with the minimum of fuss. The meter connects directly to your aerial and the
LEDs indicate the signal strength. The five green LEDs; indicate signal power
values; 50dBµV, 60dBµV, 70dBµV, 80dBµV, allowing you to visualise your TV signal
strength in order to tune your TV’s antenna.
POweR SOURCe
In order to supply power to your Digital TV Signal Meter, you have to open the door
of the battery carrier at the rear of your Digital TV Signal Meter and fit a 9V Size
battery then replace the battery carrier door and close it. (Battery is supplied.
Alternatively, you can also power the unit with a 5-12V DC adaptor fitted with a 3.5
mm jack plug- not supplied).
TeSTINg fOR SIgNal
1. Turn on the power switch on the right hand side of the digital TV Signal Meter;
the red power indicator will light.
2. Point your aerial in the same direction as any visible neighbouring aerials
and then turn slowly in a horizontal arc. Continue turning in the same
direction until you find the direction in which the maximum number of LED’s
are lit. If there is more than one direction with the same maximum LED count,
select the one that covers the widest arc.
3. Finally, position your aerial at the estimated mid-point of the range in which
the maximum numbers of LEDs are lit.
SPeCIfICaTIONS
Frequency range:
40-862 MHz
Input Level:
50-90dBµV
Power Requirement:
5VDC, 40mA
External Power Source:
5-12VDC
Battery Type:
9V Size (Extra Heavy Duty type supplied)
aCCeSSORIeS
Two plastic protective cover for female F-connectors. Two F to PAL male adaptor
for female F-connectors to adapt to PAL type connecting leads if required.
One 9V size Extra Heady Duty battery to supply the digital TV signal meter.
waRRaNTy
Arlec guarantees this product in accordance with the Australian Consumer Law.
Arlec also warrants to the original first purchaser of this product (“you”) from a
retailer that this product will be free of defects in materials and workmanship for a
period of 12 months from the date of purchase; provided the product is not used other
than for the purpose, or in a manner not within the scope of the recommendations
and limitations, specified by Arlec, is new and not damaged at the time of
purchase, has not been subjected to abuse, misuse, neglect or damage, has not
been modified or repaired without the approval of Arlec and has not been used for
commercial purposes (“Warranty”).
If you wish to claim on the Warranty, you must, at your own expense, return the
product, and provide proof of original purchase and your name, address and
telephone number, to Arlec at the address below or the retailer from whom you
originally purchased the product within 12 months from the date of purchase.
Arlec will (or authorise the retailer to) assess any claim you may make on the
Warranty in the above manner and if, in Arlec’s reasonable opinion, the Warranty
applies, Arlec will at its own option and expense (or authorise the retailer to)
replace the product with the same or similar product or repair the product and
return it to you or refund the price you paid for the product. Arlec will bear its own
expenses of doing those things, and you must bear any other expenses of claiming
on the Warranty. The Warranty is in addition to other rights and remedies you may
have under a law in relation to the product to which the Warranty relates.
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure
and for compensation for any other reasonably foreseeable loss or damage. You
are also entitled to have the goods repaired or replaced if the goods fail to be of
acceptable quality and the failure does not amount to a major failure.
Green Signal
Strength LEDs
TV
AP9000_ Instructions.indd 4
16/01/12 2:08 PM
