Antrica ANT-35000A Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 68

Antrica ANT-35000A Скачать руководство пользователя страница 10

!

/

!

10 68

ANT-35000A

User Manual

2. Installation

Connecting Video

-

PC

Encoder System

Connect PC video output line to the encoder (video server) video input port.

-

Connecting with Megapixel Camera

Connect a camera which supports HDMI or 3G/HD-SDI output to the HDMI or 3G/HD-SDI Input port of
video server accordingly.

-

Connecting with D1 resolution Camera

Connect a camera to the Video Input port of video server accordingly.

Connecting Audio

It is possible to set the mode as Tx-only or audio off.

-

Connect audio input and output ports to audio devices accordingly.

-

The Audio signal required is line level, 1volt Pk Pk so audio equipment with an amp, mixer or other

amplifier should be used.

Connecting Serial Ports

For camera control, PTZ controller (keyboard) and receiver can be connected to serial ports. Two
corresponding serial ports in encoder and decoder which are connected in 1-to-1 fashion works in pass-
through mode. This means that commands at a local system’s COM1 port will be transparently passed to the
remote system’s COM1 port. Also, a command at a local system COM2 port will pass to the remote system’s
COM2 port.

Connecting Sensor and Alarm

Connect sensor and alarm devices to corresponding terminals accordingly.

Connecting Power

After confirming the power source, connect power adaptor and connect the 12VDC connector to the system.

Check if it Works

Once the power is supplied to the camera, it will start booting. The system will boot up to an operating mode
after approximately 40-60 seconds. The green LED on the Ethernet port will flash indicating the system is
ready.

Page 7 of 7

10

68

«
...
8
9
10
11
12
...
»

Содержание ANT-35000A





































































Отзывы:

Нет отзывов