Trolley Cart
Anthro
®
Corporation Technology Furniture
®
10450 SW Manhasset Drive Tualatin, Oregon 97062 anthro.com
Step 3
(requires the 6mm Hex Key)
Position both Trunk Assemblies and the 18” Lower Cross Tube
as shown.
Insert the 18” Cross Tube into the Large Holes of each Trunk
and loosely attach the Tube to each Trunk using one Tube
Screw per end.
NOTE: The 18” Cross Tube ends are keyed to fit into the Trunk
Assemblies.
NOTE: If you purchased a Trolley Base Shelf, install the Casters
to the Trunk Assemblies during this Step.
anthro.com
Step 5
(requires the 3-Way Wrench)
Position one Trolley Shelf & Handle Side against a Trunk As-
sembly. Insert the two posts of a Side into holes 3 & 5 (from
the top) of the Trunk. Loosely attach the Side to the Trunk
with one Button Head Screw and Keps Nut. Repeat for the
other Side.
Place the Trolley Handle between both Sides. Insert a Handle
Screw through both ends of the Side and carefully thread into
the Handle. Tighten the Button Head Screws on the Sides.
NOTE: By installing the Side posts into holes 3 & 5, your final
Shelf height will be 36” from the floor.
Questions? 1-800-325-3841
Step 2
(requires the 3-Way Wrench)
STOP: If yOU PURCHASEd A TROllEy BASE SHElf, REAd THOSE
INSTRUCTIONS NOw.
Install all four Casters to both Trunk Assemblies using four Button
Head Screws per Caster.
DOUBLE CHECK THE INSTALLATION of the Swivel Lock Casters
(Green Brake Pedal)
by positioning the Trunk Assembly & Caster
as shown. Then depress the Brake. If it is installed correctly, the
Caster will be locked in a parallel orientation
(as shown)
with the
Trunk Assembly.
NOTE: Make certain to install one Swivel Lock Caster (green brake)
and one Total Lock Caster (black brake) onto each
Trunk Assembly.
Step 4
(requires the 6mm Hex Key)
Rotate the Cart Assembly
(from Step 3)
onto the Casters.
Place the 12” Upper Cross Tube between each Trunk Assembly
and align the Tube with the Large hole, midway
up the Trunk.
Carefully secure into place using one Tube Screw per end.
(
5
/
16
-18 X 1”) Tube Screw
325-5136-00
(
5
/
16
-18 X 3/4”) Button Head Screw
325-5188-00
(
1
/
4
-20 X .375”) Button Head Screw
325-5210-00
(
1
/
4
-20) Keps Nut
325-5202-00
(
5
/
16
-18 X 1”) Tube Screw
325-5136-00
(
1
/
4
-20 X .375”) Button Head Screw
325-5210-00
(
1
/
4
-20) Keps Nut
325-5202-00
(
1
/
4
-20 X 2”) Handle Screw
325-5034-00
Total lock Caster
(Black Brake Pedal)
front position
Swivel lock Caster
(green Brake Pedal)
rear position
Trunk Assembly (y)
Trunk Assembly (X)
keyed Cross Tube
ends
large hole
Shelf & Handle Side
(X)
Trolley Handle and Shelf & Handle Side (y)
are removed for clarity.
Hole 7
Hole 9
Shelf & Handle Side
(X)
Button Head
Screw
keps Nut
Cable Hanger
Step 6
(requires the 3-Way Wrench)
Determine the location for your Trolley Cable Hangers, then
position one against a Trunk Assembly.
Insert two Button Head Screws through the Cable Hanger and
capture on the opposite side using two Keps Nuts.
Repeat for remaining Cable Hanger.
Step 1
BEFORE YOU BEGIN, take special notice of the features on the
Swivel Lock Casters
(those with the Green Brake Pedals).
The teeth on the plate of both Swivel Lock Casters need to face
the rear of the Trunk Assemblies.
Step 2 will give further instructions about securing the
Casters to the Trunk Assemblies.
Teeth
(on the Plates) faces the rear of
the Trunk Assemblies
Plate
Installed to the Trunk
Assemblies
NOTE: There are a matching set
of teeth on the truck. Since the
truck rotates, their orientation is
not critical.
Swivel lock Caster
(green Brake Pedal)
Rear of the Trunk As-
semblies
Truck
Trunk Assembly (y)
large hole
12” Cross Tube
Shelf & Handle Side
(y)
Handle Screw
Button Head Screw
keps Nut
Hole 3
Hole 5
Post
