ANTAIRA LNX-C501G-SFP Series Скачать руководство пользователя страница 12

Страница: 12 / 23

Antaira Technologies - Industrial Ethernet Switches

LNX-C501G-SFP Series - Hardware Manual - v1.0

1 / RX+

3 / TX+

1 / RX+

1 / TX+

2 / RX-

6 / TX-

2 / RX-

2 / TX-

3 / TX+

1 / RX+

3 / TX+

3 / RX+

6 / TX-

2 / RX-

6 / TX-

6 / RX-

Table 2.4 - 10/100Base-T(X) RJ45 Pin Assignments

Crossover Cable

Straight Through Cable

Pin Number / Signal

1 / TP0+

3 / TP1+

1 / TP0+

1 / TP1+

2 / TP0-

6 / TP1-

2 / TP0-

2 / TP1-

3 / TP1+

1 / TP0+

3 / TP1+

3 / TP0+

4 / TP2+

7 / TP3+

4 / TP2+

4 / TP3+

5 / TP2-

8 / TP3-

5 / TP2-

5 / TP3-

6 / TP1-

2 / TP0-

6 / TP1-

6 / TP0-

7 / TP3+

4 / TP2+

7 / TP3+

7 / TP2+

8 / TP3-

5 / TP2-

8 / TP3-

8 / TP2-

Table 2.5 - 1000Base-T RJ45 Pin Assignments

Note:

“+” and “-” signs represent the polarity of the wires that make up each wire pair.

2.7 Cabling

Use the four twisted-pair, category 5e, or the above cabling for the RJ45 port connections. The cable between the switch

and the link partner (switch, hub, workstation, etc.) must be less than 100 meters (328 ft.) in length.

The small form-factor pluggable (SFP) is a compact optical transceiver used in optical communications for both

telecommunication and data communication applications.

Caution:

Please employ an optional optical transceiver (SFP/Fixed Fiber) that complies with IEC 60825-1 and

classiﬁed as Class 1 laser product.

Attention:

Veuillez utiliser un émetteur-récepteur optique en option (SFP/ﬁbre ﬁxe) conforme à la norme IEC

60825-1 et classé comme produit laser de classe 1.

Содержание LNX-C501G-SFP Series
























Результаты поиска

Содержание LNX-C501G-SFP Series

Отзывы:

Похожие инструкции для LNX-C501G-SFP Series

Бренды по названию

Популярные бренды

ANTAIRA LNX-C501G-SFP Series, Руководство по оборудованию

Результаты поиска

Содержание LNX-C501G-SFP Series

Отзывы:

Похожие инструкции для LNX-C501G-SFP Series

Бренды по названию

Популярные бренды