ANTAIRA LNP-1204G-SFP Series Скачать руководство пользователя страница 22

Страница: 22 / 23

Antaira Technologies - Industrial Ethernet Switches

LNP-1204G-SFP Series User Manual V1.0

7. Technical Specifications

Table 7.1

has the technical specifications for Antaira

’s LNP-1204G-SFP series: 12-port industrial

PoE+ gigabit unmanaged Ethernet switch with 8*10/100/1000Tx (30W/Port), and 4*100/1000 SFP

slots, 48~55VDC input.

Standards

IEEE 802.3

10Base-T 10Mbit/s Ethernet

IEEE 802.3u

100Base-Tx, 100Base-Fx, Fast Ethernet

IEEE 802.3ab

1000Base-Tx Ethernet

IEEE 802.3z

Gigabit Fiber

IEEE 802.3at

Power-over-Ethernet Plus (Enhanced)

Switch

Property

Protocol

CSMA/CD

Data Process

Store and Forward

Transfer rate

14,880 pps for 10Base-T Ethernet port

148,800 pps for 100Base-TX Fast Ethernet port

1,488,000 pps for gigabit Ethernet port

Transmission Distance

Up to 100M (Fast Ethernet)

Transmission Speed

Up to 1000Mbps

MAC Address Table

8K table size

MAC Table

Port Interface

Ethernet (RJ45) Port

8*10/100/1000Tx (30W/Port) auto negotiation speed, full/half duplex

mode, and auto MDI/MDI-X connection

PoE Pin Assignment

V+, V+, V-, V-, for pin 1, 2, 3, 6 (Endspan, MDI Alternative A)

Fiber

– SFP Slot

4*SFP Slots support dual rate 100/1000

Wavelength

Refer to SFP Module

LED Indicator

Power Unit: P1 (Green), P2 (Green),fault(Red)

Ethernet port: Link/active(Green), 1000Mbps

SFP : Link/active(Green)

Network Cable

10BaseT: 2-pair UTP/STP Cat.3,4,5 cable EIA/TIA-568 100-ohm (100m)

100BaseTX: 2-pair UTP/STP Cat.5 cable EIA/TIA-568 100-ohm (100m)

1000BaseTX: UTP/STP Cat.5/5E cable EIA/TIA-568 100-ohm (100m)

Mechanical

Characteristics

Housing

Metal IP30 protection

Dimension

46 x 142 x 99 mm

Weight

Unit Weight: 1.8 lbs. Shipping Weight: 2.3 lbs.

Mounting

DIN-Rail Mounting, wall-mounting (optional)

Power

Requirement

Input Voltage

48~55VDC Redundant Input

Power Connection

1 removable 6-contact terminal block

Fault Output

1 Relay output

PoE Power Output

25W @ 48VDC (per PoE port); 30W @ 51~55VDC (per PoE port)

Power Consumption

215W@48V / 255W@51~55V (Full Load with PoE Function)

Environmental

Limits

Operating Temperature

Standard: -10 to 70C (14 to 158F)

EOT: -40 to 75C (-40 to 167F)

Operating Humidity

5% to 95% (Non-Condensing)

Storage Temperature

-40 to 85C (-40 ~ 185F)

Содержание LNP-1204G-SFP Series
























Результаты поиска

Содержание LNP-1204G-SFP Series

Отзывы:

Похожие инструкции для LNP-1204G-SFP Series

Бренды по названию

Популярные бренды

ANTAIRA LNP-1204G-SFP Series, Руководство пользователя

Результаты поиска

Содержание LNP-1204G-SFP Series

Отзывы:

Похожие инструкции для LNP-1204G-SFP Series

Бренды по названию

Популярные бренды