ANTAIRA LNP-0702C-SFP Series Скачать руководство пользователя страница 22

Страница: 22 / 23

Antaira Industrial Ethernet Switches

LNP-0702C-SFP Series User Manual V1.0

7. Technical Specifications

Table 7.1 has the technical specifications for Antaira

’s LNP-0702C-SFP series: 7-port industrial

PoE+ gigabit unmanaged Ethernet switch with 4*10/100Tx (30W/Port), 1*10/100Tx, and

2*100/1000 SFP slots.

Standards

IEEE 802.3 10BaseT Ethernet

IEEE 802.3u 100BaseTX Fast Ethernet

IEEE 802.3z gigabit Fiber

IEEE 802.3at power over Ethernet

Protocol

CSMA/CD

Transfer Rate

14,880pps for Ethernet port

148,800pps for fast Ethernet port

Transmission Distance

Up to 100M (Fast Ethernet)

Transmission Speed

Up to 1000Mbps

MAC Address

8K table size

RJ45 (Ethernet) Port

4*10/100Tx (30W/Port) + 1*10/100Tx auto

negotiation speed, full/half duplex mode, and auto

MDI/MDI-X connection

PoE Pin Assignment

RJ-45 port #1 ~ # 4 support IEEE 802.3at end-

point, alternative A mode.

Positive (VCC+): Pin 1, 2

Negative (VCC-): RJ-45 pin 3, 6

Data: Pin 1, 2, 3, 6

SFP Slot

2*SFP slots support dual rate 100/1000

LED

Power Unit: P1 (Green), P2 (Green),fault(Red)

Ethernet port: Link/active(Green), 10/100Mbps

SFP: Link/active(Green)

Network Cable

10BaseT: 2-pair UTP/STP Cat. 3, 4, 5 cable

EIA/TIA-568 100-ohm (100m)

100BaseTX: 2-pair UTP/STP Cat. 5 cable

EIA/TIA-568 100-ohm (100m)

Over Current Protection

Single-blown fuse

Power Input

Redundant power DC 48~55V with connective

1*6-pin removable terminal block

Fault Output

1 Relay output

Содержание LNP-0702C-SFP Series
























Результаты поиска

Содержание LNP-0702C-SFP Series

Отзывы:

Похожие инструкции для LNP-0702C-SFP Series

Бренды по названию

Популярные бренды

ANTAIRA LNP-0702C-SFP Series, Руководство пользователя

Результаты поиска

Содержание LNP-0702C-SFP Series

Отзывы:

Похожие инструкции для LNP-0702C-SFP Series

Бренды по названию

Популярные бренды