ANTAIRA LNP-0501 Series Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 21

background image

Antaira Technologies - Industrial Ethernet Switches

LNP-0501 Series User Manual V2.2

3

2. Hardware Description

2.1 Physical Dimensions

Figure 2.1, below, shows the physical dimensions of Antaira Technologies’ LNP-0501 series: 5-port

industrial PoE+ unmanaged Ethernet switch with 4*10/100Tx (30W/port), 1*100Fx Fiber SC/ST type

connector (Multi-mode 2Km, or Single-mode 30Km).

(W x D x H) is 30mm x 99mm x 142mm

Figure 2.1

LNP-0501 Series Physical Dimensions

«
...
5
6
7
8
9
...
»

Содержание LNP-0501 Series






















Отзывы:

Нет отзывов

Похожие инструкции для LNP-0501 Series

Бренд: D-Link Страницы: 14

Бренд: Fairchild Страницы: 14

Бренд: Maipu Страницы: 21

Бренд: Maico Страницы: 56

Бренд: ifs Страницы: 352

Бренд: LevelOne Страницы: 17

Бренд: StarTech.com Страницы: 10

Бренд: Clever Little Box Страницы: 15

Бренд: Tripp Lite Страницы: 12

Бренд: UniFi Страницы: 8

Бренд: GarrettCom Страницы: 39

S5130S-EI series

Бренд: H3C Страницы: 67

Бренд: Davey Страницы: 2

Бренд: hager Страницы: 72

Бренд: Kramer Страницы: 2

AVS-OCT-4832-117

Бренд: AMX Страницы: 1

Бренд: Little Giant Страницы: 8

IPES/IES-5416T Series

Бренд: Lantech Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды