ANTAIRA LMP-C602G-SFP-bt-T-V2 Скачать руководство пользователя страница 16

Страница: 16 / 28

Antaira Technologies - Industrial Ethernet Switches
LMP-C602G-SFP-bt-V2 Series - Hardware Manual - v1.0

* Note:

When the relay is triggered because of event 2~5, the relay contact alarm will update the status every 30

seconds. If there is no event happening for 30 seconds, the relay contact alarm will be turned off. If the

user disables the failed PoE port by removing the cable or DIP switch manually, the relay will be recovered

immediately.

2.7 Reset Button

There is a “reset” button located on the top panel of the industrial Ethernet switch that helps users to

reboot, restore default, or save running configurations by pressing the button for different seconds.

Please refer to Table 2.3 for the timing and function.

Table 2.3 - Reset Button Functions

2.8 Ethernet Ports

●

RJ45 Ports

RJ45 Ports (Auto MDI/MDI-X): The RJ45 ports are auto-sensing for 10Base-T, 100Base-TX, or

1000Base-T connections. Auto MDI means that the switch can connect to another switch or workstation

without changing the straight-through or crossover cabling. See the figures below for straight-through and

crossover cabling schematics.

●

RJ45 Pin Assignments

Table 2.4 - 10/100Base-T(X) RJ45 Pin Assignments

Seconds

Function

Fault LED

0s < t (press time) < 4s

Reboot the switch

LED is flashing with green color

4s < t (press time)

Restore factory default

LED is flashing with green and red color

Crossover Cable

Straight Through Cable

Pin Number / Signal

1 / RX+

3 / TX+

1 / RX+

1 / TX+

2 / RX-

6 / TX-

2 / RX-

2 / TX-

3 / TX+

1 / RX+

3 / TX+

3 / RX+

6 / TX-

2 / RX-

6 / TX-

6 / RX-

Содержание LMP-C602G-SFP-bt-T-V2





























Результаты поиска

Содержание LMP-C602G-SFP-bt-T-V2

Отзывы:

Бренды по названию

Популярные бренды

ANTAIRA LMP-C602G-SFP-bt-T-V2, Руководство по оборудованию

Результаты поиска

Содержание LMP-C602G-SFP-bt-T-V2

Отзывы:

Бренды по названию

Популярные бренды