ANTAIRA LMP-1802G-M12-10G-SFP-67-110 Series Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 26

background image

Antaira Technologies - Industrial Ethernet Switches

LMP-1802G-M12-10G-SFP-67-110 Series - Hardware Manual - v1.0

5 Technical Speciﬁcations

Table 5.1

has the technical speciﬁcations for this product series.

Technology

L2 Switching

Port/MAC/Protocol/IP Subnet-based VLAN, GARP/GVRP, Loop Guard, Link
Aggregation static/LACP, BPDU guard, Error disable recovery, IGMP snooping
v2/v3, MLD snooping v1/v2, IGMP ﬁltering, IPMC throttling / ﬁltering leave
proxy, DHCP snooping, G.8032 v1/v2

L3 Switching

DHCP option82, static routes

QoS

802.1p Queueing, Input priority mapping, Storm control for
Unicast/Multicast/Broadcast, Port/Queue/ACL policer, Port egress shaper,
Queue egress shaper, DiffServ (DSCP), Tag remarking, Scheduler mode

Power Saving

ActiPHY, PerfectReach, IEEE 802.3az EEE power management

Network Redundancy

STP/RSTP/MSTP, port trunk with LACP, ERPS v1/v2 (<50ms)

Conﬁguration

Http, Https, Telnet, SSH, CLI, TFTP, SNMP v3

System / Diagnostics

Dual Image Protection, PING, PING6

Switch Properties

Switch Architecture

Back-Plane (Switching Fabric): 72.0Gbps

Priority Queues

8

Processing Type

Store and Forward

Flow Control

IEEE 802.3x for full duplex mode, back pressure for half duplex mode

Transfer Rate

14,880pps for 10Base-T Ethernet
148,800pps for 100Base-T Fast Ethernet
1,488,000pps for Gigabit Ethernet
14,880,000pps for 10 Gigabit Ethernet

Memory Buffer

4Mbits

Jumbo Frame

9.6Kbytes

MAC Table Size

32K

VLAN Group

4095

IGMP Group

1024

Port Interface

Ethernet Port

16*10/100/1000BaseTx, 8-pin M12 X-Coded female connectors
Auto-negotiation speed, Full/Half duplex mode, and auto MDI/MDI-X

«
...
22
23
24
25
26
»

Содержание LMP-1802G-M12-10G-SFP-67-110 Series



























Отзывы:

Нет отзывов

Похожие инструкции для LMP-1802G-M12-10G-SFP-67-110 Series

Бренд: D-Box Страницы: 27

Бренд: Kramer Страницы: 8

Бренд: Top View Страницы: 2

Бренд: Kramer Страницы: 17

SmartSwitch 2500

Бренд: Cabletron Systems Страницы: 402

Бренд: IOGear Страницы: 1

Бренд: 3onedata Страницы: 4

Бренд: H-Tronic Страницы: 15

GlobeCaster STUDIO 4000

Бренд: Global Streams Страницы: 144

TNM4000-TP36FF4X16G24P

Бренд: MRD Страницы: 38

Бренд: IDT Страницы: 158

IIOT-AMS Tilt Counter

Бренд: ROSSMA Страницы: 13

Бренд: Sven Страницы: 4

Бренд: Lindy Страницы: 12

S-Mix-Pro 18*18

Бренд: Kensence Страницы: 24

CT.TS005.501401

Бренд: Talkswitch Страницы: 9

Бренд: Fastcabling Страницы: 4

Бренд: Dwyer Instruments Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды