background image

Antaira Technologies - Industrial Wireless Access Points

ARS-7235-5E-AC Series - Hardware Manual - v1.0

The Ethernet port’s (RJ45) LED on the industrial wireless access point will turn on when the

cable is connected to the networking device.

Please refer to the

LED Indicators

section for LED light indication.

7. When all connections are set and the LED lights all show normal, the installation is complete.

4.2 Maintenance and Service

If the device requires servicing of any kind, the user is required to disconnect and remove it from

its mounting. The initial installation should be done in a way that makes this as convenient as

possible.

Voltage / Power lines should be properly insulated as well as other cables. Be careful when

handling them so as to not trip over.

Do not under any circumstance insert foreign objects of any kind into the heat dissipation

holes located in the different faces of the device. This may not only harm the internal layout,

but might cause harm to users as well.

Do not under any circumstance open the device for any reason. Please contact your dealer

for any repair needed or follow the instructions within the manual.

Clean the device with dry soft cloth.

4.3 Troubleshooting

Always verify the right power cord or adapter is being used. Never use a power supply or adapter

with a non-compliant DC output voltage or it will burn the equipment.

Select the proper UTP or STP cable in order to construct the network. Use an unshielded

twisted-pair (UTP) or shield twisted-pair (STP) cable for RJ45 connections: 100Ω Category 5e for

10/100Mbps. Also be sure that the length of any twisted-pair connection does not exceed 100

meters (328 feet).

Diagnosing LED Indicators: To assist in identifying problems, the switch can be easily monitored

with the LED indicators which help to identify if any problems exist.

Please refer to the LED Indicators section for LED light indication.

15

Содержание ARS-7235-5E-AC Series
























Отзывы: