Anritsu 3659 Скачать руководство пользователя страница 14

Страница: 14 / 160

2-4 0.8 mm Verification Application Installation

Using the 2300-580-R Software with VectorStar ME7838D

2-2

PN: 10410-00327 Rev. D

3659 0.8 mm Cal/Ver Kit & 2300-580-R PVS UG

2-4

0.8 mm Verification Application Installation

Prior to installation of the 0.8 mm Application, the National Instruments GPIB card and drivers must be
installed in the Windows PC.
This needs to be done only once per PC Controller. The software is contained on the

Disk supplied with each

Verification Kit.

Prior to installation of the verification software, the National Instruments GPIB card and its drivers
must be installed in the PC Controller.

Turn off all other running applications on the PC Controller.

Insert the USB drive into the PC Controller USB slot.

Open

Windows Explorer

, browse to the USB Drive, and double click on

Startup.htm.

The Verification Software navigation page (

Figure 2-1

) should then appear.

On the navigation page, click the

Install Anritsu 0.8 mm Verification Application Software

link.

The first of several installation dialog boxes appears.

Note

In order to correctly install the PVS application, the user (logged in) must have Administrative rights
on the Windows PC Controller.

Figure 2-1.

PVS Installation and Documentation Screen

Содержание 3659

































































































































































Результаты поиска

Содержание 3659

Отзывы:

Anritsu 3659, Руководство пользователя, Страница: 14 / 160

Результаты поиска

Содержание 3659

Отзывы: