manualshive.com logo in svg

Anritsu 3659, Руководство пользователя, Страница: 13 / 160

Поделиться
Скачать
Anritsu 3659 Скачать руководство пользователя страница 13

3659 0.8 mm Cal/Ver Kit & 2300-580-R PVS UG

PN: 10410-00327  Rev. D

2-1

Chapter 2 — Using the 2300-580-R Software 
with VectorStar ME7838D

2-1

Introduction

This chapter describes the use of the Anritsu 2300-580-R Performance Verification Software (PVS) with the 
VectorStar ME7838D Modular BB/mm-Wave VNA Measurement System. The ME7838D is based on the 
VectorStar MS4647A/B Vector Network Analyzer running VectorStar for the MS4647B model Application 
Version 2.1.0 or higher and equipped with Option 08x or the MS4647A model Application Version 1.7.6 and 
equipped with Option 08x. 

2-2

Required Equipment

Required VectorStar ME7838D Broadband System, 70 kHz to 145 GHz Instruments and 
Components

The VectorStar ME7838D Broadband/Millimeter Wave Measurement System consists of:

•

VectorStar MS4647A/B VNA, 70 kHz to 70 GHz, V Connectors, equipped with Option 08x 

•

3739C Broadband Test Set

•

Two (2) MA25300A Millimeter-Wave (mm-Wave) Modules, 70 kHz to 145 GHz.

•

Necessary rear panel interconnect cables between the test set and the VNA.

•

Necessary front panel interconnect cables between the test set and the VNA

•

Necessary interconnect cables to the MA25300A mm-Wave Modules.

2-3

Configuring the Hardware

This section describes how the various system elements are interconnected and describes the preliminary steps 
required for operation of the verification software. See 

“Required VectorStar ME7838D Broadband System, 70 

kHz to 145 GHz Instruments and Components” on page 2-1

 above for a complete equipment list. 

1. 

Ensure that the VNA system is set to “Broadband”.

2. 

To verify the setting, from the right side 

MAIN

 menu, select the broadband test set button:

•

MAIN | Application | APPLICATION | Rcvr Config | RCVR CONFIG | BB/mmWave (3738 Test Set) or 

BB/mmWave (3739 Test Set)

3. 

Select the 

Baseband

 Receiver Configuration.

4. 

Connect a GPIB cable between the PC Controller and the VNA Rear Panel GPIB port labeled IEEE 488.2 

GPIB. 

Note

Anritsu does not support tests or verification processes for wafer probe equipment. Contact the 
vendor of the wafer probe equipment if such support is desired. 

Caution

Do not connect the cable to the VNA Rear Panel GPIB port labeled 

Dedicated GPIB

. 

Содержание 3659

































































































































































Отзывы:

Нет отзывов