Anritsu 3659 Скачать руководство пользователя страница 109 | Manualshive

Страница: 109 / 160

Anritsu 3659 Скачать руководство пользователя страница 109

3659 0.8 mm Cal/Ver Kit & 2300-580-R PVS UG

PN: 10410-00327 Rev. D

4-1

Chapter 4 — Using the 2300-580-R Software
with VectorStar ME7838G

4-1

Introduction

This chapter describes the use of the Anritsu 2300-580-R Performance Verification Software (PVS) with the
VectorStar ME7838G Modular BB/mm-Wave VNA Measurement System. The ME7838G is based on the
VectorStar MS4647B Vector Network Analyzer running VectorStar for the MS4647B model Application
Version 2.1.0 or higher and equipped with Option 08x.

4-2

Required Equipment

Required VectorStar ME7838G Broadband System, 70 kHz to 220 GHz Instruments and Components
(Verification will be done to 145 GHz with the 3659 kit and the 2300-580-R software).
The VectorStar ME7838G Broadband/Millimeter Wave Measurement System consists of:

•

VectorStar MS4647B VNA, 70 kHz to 70 GHz, V Connectors, equipped with Option 08x

•

3739C Broadband Test Set

•

Two (2) MA25400A Millimeter-Wave (mm-Wave) Modules, 70 kHz to 220 GHz

•

Two (2) 33.8G50 adapters to convert the native flange-based interface of the MA25400A to a 0.8 mm

male connector

•

Necessary rear panel interconnect cables between the test set and the VNA

•

Necessary front panel interconnect cables between the test set and the VNA

•

Necessary interconnect cables to the MA25400A mm-Wave Modules

4-3

Configuring the Hardware

This section describes how the various system elements are interconnected and describes the preliminary steps
required for operation of the verification software. See

“Required Equipment”

above for a complete equipment

list.

1.

Ensure that the VNA system is set to “Broadband”.

2.

To verify the setting, from the right side

MAIN

menu, select the broadband test set button:

•

MAIN | Application | APPLICATION | Rcvr Config | RCVR CONFIG | BB/mmWave (3739 Test Set)

3.

Select the

Baseband

Receiver Configuration.

4.

Connect a GPIB cable between the PC Controller and the VNA Rear Panel GPIB port labeled IEEE 488.2

GPIB.

Note

Anritsu does not support tests or verification processes for wafer probe equipment. Contact the
vendor of the wafer probe equipment if such support is desired.

Caution

Do not connect the cable to the VNA Rear Panel GPIB port labeled

Dedicated GPIB

.

«
...
107
108
109
110
111
...
»

Содержание 3659

































































































































































Отзывы:

Нет отзывов