Anritsu Company Site Master S312D Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 62

Anritsu Company Site Master S312D Скачать руководство пользователя страница 43

Removal and Replacement

3-2

Battery Information

S312D MM

PN: 10580-00195 Revision B

3-3

Battery Testing Procedure

1.

With the Site Master

Off

and the battery installed, connect the Universal AC Adapter to the

12.5–15VDC (1350 mA) connector. The External Power LED and the Battery Charging LED will light.

2.

Disconnect the AC-DC Adapter when the Battery Charging LED turns off (indicating that the battery is
fully charged).

3.

Press and hold the

ESCAPE/CLEAR

key, then press the

ON/OFF

key to turn on the Site Master. This sets

the instrument to the factory preset state. Press

ENTER

when prompted to continue.

4.

Press the

SYS

key, followed by the

STATUS

soft key. Verify that the indicated battery charge is

≥

80%. If

the value is 80% or above, then press the

ESCAPE/CLEAR

key and continue with this procedure. If the

value is lower than 80%, then a discharge/charge cycle may be needed in order to improve the battery
capacity. Completely discharge the battery, as described in Step

and Step

below, and then recharge

the battery as described in Step

and Step

. If the battery capacity does not increase after a discharge/

charge cycle, then replace the battery.

5.

Press the

START CAL

key (to keep the Site Master from going into HOLD mode) and make note of the

test start time.

6.

When the Site Master display fades and the Site Master switches itself off, make note of the test stop
time.

7.

The total test time (Step

to Step

≥

1.5 hours. If the battery charge started at 80% or more,

and if the total battery test time is < 70 minutes, then replace the battery.

Note

If the Battery Charging LED does not light, the battery may be too low to immediately begin full
charging. Leaving the instrument connected to AC power for several hours may bring the battery up
to a level at which full charging can begin. Turn the instrument off and back on to see if the Battery
Charging LED lights indicate that a full charge cycle has begun.

Charging is inhibited below 0

°

C and above 45

°

C. If the instrument is too hot, the battery will not start

charging until the instrument temperature has cooled to 43

°

C.

«
...
41
42
43
44
45
...
»

Содержание Site Master S312D































































Отзывы:

Нет отзывов