Annovi Reverberi Blue Clean 1310, Оригинальное руководство пользователя

Страница: 13 / 84

13
English
EN
4
GENERAL INFORMATION (FIG.1)/PAGE 3
4.1 Use of the manual
The manual forms an integral part of the machine and should be
kept for future reference. Please read it carefully before installing/
using the machine. If the machine is sold, the seller must pass on
this manual to the new owner along with the machine.
4.2 Delivery
The machine is delivered partially assembled in a cardboard box.
The supply package is illustrated in fig.1.
4.2.1 Documentation supplied with the machine
A1 Use and maintenance manual
A2 Safety instructions
A3 Declaration of conformity
A4 Warranty regulations
4.3 Disposing of packaging
The packaging materials are not environmental pollutants but must
still be recycled or disposed of in compliance with the relevant
legislation in the country of use.
5
TECHNICAL INFORMATION (FIG.1)/PAGE 3
5.1 Intended use
This machine has been designed for individual use for the cleaning
of vehicles, machines, boats, masonry, etc., to remove stubborn dirt
using clean water and biodegradable chemical detergents.
Vehicle engines may be washed only if the dirty water is disposed of
as per regulations in force.
- Inlet water temperature: see machine data plate.
- Inlet water pressure: min. 0.1 MPa - max. 1 MPa.
- Operating ambient temperature: above 0 °C.
The machine is compliant with the IEC 60335-1 and IEC 60335-2-79
standards.
5.2 Operator
The symbol in fig.1 identifies the machine’s intended operator.
5.3 Main components
B2 Lance
B3 Trigger gun with safety catch
B4 Power cable
B5 High pressure hose
B7 Oil cap
B8 Diesel tank
B9 Front diesel filter
B10 Rear diesel filter
B12 Boiler exhaust
E Nozzle
G Pressure regulator
L Water filter
V Water nozzle
Z Control panel
5.3.1 Accessories (where supplied - see fig.1)
C2
Rotary nozzle kit
C3
Handle
C5
Hose reel
C9
Adaptor
C10
Screws
C11
Brackets
C12
Lever
C13
Detergent kit
C14
Wheels
C16
Pressure gauge
C21
Power on light
5.3.2
Control panel (see fig.1)
- Machine switch (
H
)
OFF/0 - ON/I Cold water operation.
- Hot water operation switch (
T
)
0/OFF - ON/I Hot water operation.
- Temperature setting thermostat (Y) for hot water operation.
- Power on light (C21/1325)
5.4 Safety devices
- Starter device (H).
The starter device prevents accidental use of the machine.
- Boiler starter device (
T
).
Warning - danger!
Do not tamper with or adjust the safety valve setting.
- Safety and/or relief valve.
The safety valve is also a relief valve.
- Safety catch (D): prevents accidental emission of water jet.
- Overload cutout: stops the machine in case of overload (1310 -
1320 - HOT 1310 INOX).
- Magneto-thermic switch: cuts out the machine in case of overload
(1325).
6
INSTALLATION (FIG.2)/PAGE 4
6.1 Assembly
Warning - danger!
All installation and assembly operations must be per-
formed with the machine disconnected from the mains power
supply.
The assembly sequence is illustrated in fig.2.
6.2 Fitting the rotary nozzle
(For models with this feature).
The rotary nozzle kit delivers greater washing power.
Use of the rotary nozzle may cause a reduction in pressure of 25%
compared to the pressure obtained with the adjustable spray
nozzle. However, the rotary nozzle delivers greater washing power
due to the rotation of the water jet.
6.3 Electrical connection
Warning - danger!
Check that the electrical supply voltage and frequency
(V-Hz) correspond to those specified on the data plate (fig.2).
6.3.1 Use of extension cables
The cross-section of the extension cable should be pro-
portional to its length; the longer it is, the greater its
cross-section should be. See table I.
6.4 Water supply connection
Warning - danger!
Only clean or filtered water should be supplied to the
machine. The flow rate of the water inlet tap must be equal
to that of the pump.
Place the machine as close to the water supply system as possible.
6.4.1 Connection points
l
Water outlet (OUTLET)
n
Water inlet with filter (INLET)
6.4.2 Connection to the mains water supply
The machine may only be connected directly to the
mains drinking water supply if the supply hose is fitted
with a backflow preventer valve with drain facility as per
current regulations in force. Make sure that the hose is at
least Ø 13 mm, that it is reinforced and that it is not more
than 25 m long.
7
ADJUSTMENTS (FIG.3)/PAGE 5
7.1 Adjusting the detergent pressure
To deliver detergent at the correct pressure, set the nozzle (E) on
" " as shown.
The quantity of detergent delivered is adjusted using the regulator
(F) (on models with this feature).
7.2 Adjusting the working pressure
The regulator (G) is used to adjust the working pressure. The pres-
sure is shown on the pressure gauge (where fitted).
7.3 Setting the temperature
When operating with hot water, use the thermostat (Y) to set the
working temperature required.