background image

 Fig 4 

DETERGENTS 

The use of detergents can dramatically 

reduce cleaning time and assist in the 

removal of difficult stains. Some detergents 

have been customized for pressure washer 

use on specific cleaning tasks. These 

detergents are approximately as thick as 

water. The use of thicker detergents, such 

as dish soap, will clog the chemical injection 

system and prevent the application of the 

detergent. 

The cleaning power of detergents comes 

from applying them to a surface and giving 

the chemicals time to break down the dirt 

and grime. Detergents work best when 

applied at low pressure. 

The combination of chemical action and 

high pressure rinsing is very effective. On 

vertical surfaces, apply the detergent 

starting at the bottom and work your way 

upward. This will prevent the detergent from 

sliding down and causing streaks. High 

pressure rinsing should also progress from 

the bottom to top. On particularly tough 

stains, it may be necessary to use a brush 

in combination with detergents and high 

pressure rinsing. 

  Operation 

The following cleaning procedure will help 

you to organize your cleaning task, and 

ensure that you achieve the most beneficial 

results in the shortest amount of time. 

Remember to use the spraying/cleaning 

techniques previously listed. 

1. Surface preparation

Before starting a pressure wash cleaning 

10

Содержание ABW-VAV-90P

















Отзывы: