ANK 300B Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 90

background image

Copyright © 2019 ANK Audio Kits
www.AudioNoteKits.com
[email protected]

Page 6

1.1 About ANK Audio Kits

Audio  Note  (UK)  started  out  in  the  early  '90s  developing  several  DIY  audio  kits  while  they  were
building up their finished product business.  DIY Audio has a long history and it was an opportunity
for knowledgeable customers to take advantage of world class designs and components.  Audio Note
(UK)  was  focused  on  using  the  very  finest  materials  and  components  custom-made  to  their
specifications,  across  their  entire  product  line  —  from  custom  film  and  electrolytic  capacitors  to
tantalum resistors, transformers, binding posts, wires, etc.  The Kit1 300B Single Ended integrated
amplifier  was  born  during  development  of  the  Meishu  and  it  proved  to  be  extremely  popular
worldwide. The ANKit business was born!

As the finished product business and dealer network started to flourish, Audio Note (UK) eventually
moved the kit business off into a separate division;  thus, in 2004, Audio Note Kits started up and was
supported by a website so that customers not located near Audio Note (UK) dealers could order kits
and  have  them  shipped  direct.    Kit  development  continued  in  earnest  during  the  2000s  with
development assisted by Audio Note (UK) engineering.  Audio Note (UK) parts were used throughout
the  kits,  depending  on  the  various  levels  and  budgets.    By  2013,  ANK  Audio  Kits  (as  it  came  to  be
called) had developed a wide product range covering all areas of two channel audio:  a single-ended
300B product line, an EL34 classAB and single-ended product line, digital to analog converters, pre-
amplifiers, Phono stages, and Audio Note (UK) speaker kits.  The end result today is that customers
worldwide with DIY skills can now build an entire high end audio system to their liking.  With the
introduction of higher levels in 2013 and the release of the Level 5 Mentor Pre-amplifier and the DAC
5.1 Signature, some customers wanted these high end products assembled by a professional builder.
As a result, ANK Audio Kits began offering this service for Level 4 and 5 products so that a significant
investment in a kit could be turned into a work of art!  Since ANK Audio Kits was born in 2004, over
2,500 kits have been shipped to customers worldwide.  Clearly, there is a real demand for high end
audio kits and ANK Audio Kits has been delivering the goods now for 15 years.

We believe and hope that you will have a great experience building your kit and we look forward to
hearing from you about your experience.

Regards,

Brian Smith — Director ANK Audio Kits

«
...
4
5
6
7
8
...
»

Содержание 300B



























































































Отзывы:

Нет отзывов

Похожие инструкции для 300B

Бренд: NAD Страницы: 4

Бренд: ValveTrain Amplification Страницы: 6

Бренд: Audio Note Страницы: 15

Бренд: MUSIC HALL Страницы: 8

Бренд: Roksan Audio Страницы: 11

Бренд: NAD Страницы: 18

Бренд: Akai Страницы: 9

Бренд: Bazooka Страницы: 32

Бренд: PCI Страницы: 2

Бренд: Mark Страницы: 12

Бренд: Pyle Страницы: 13

Бренд: Laney Страницы: 16

Бренд: T+A Страницы: 70

Бренд: Cloud Страницы: 56

Бренд: Mirage Страницы: 10

The Spell Booster

Бренд: Olsson Страницы: 12

Бренд: Harris Страницы: 56

Бренд: Somogyi Elektronic Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды