Andor Technology Zyla sCMOS 4.2 PLUS Скачать руководство пользователя страница 62

Страница: 62 / 78

version 2.0 rev 18 Feb 2021

SECTION 4: OPERATION

4.1 Connecting your Camera and Switching it on

Ensure that the Camera on / off switch is in the OFF position AND your PC is switched OFF.

For water cooled models, ensure the cooling water supply is connected prior to powering the

camera (refer to Section 3.3).

•

Before inserting the 12V DC power connector to the rear of the camera, ensure the orientation is
correct.

Never

forcibly insert the connector. For water-cooled models, connect water cooling hoses

(see

Section 3.3.2

) and ensure re-circulator/chiller is on.

•

Securely connect the Camera to PC cable between the appropriate connector(s) on the rear of the
camera and the corresponding port on the PCIe card.

(See

Figure 36

, please refer also to diagram in

Section 3.5

for correct PCIe slot connection).

Notes:

Andor Camera Link cables are labelled to assist correct installation.

For USB 3.0 models, use only the supplied USB 3.0 cable to ensure performance.

• If required connect the I/O expander cable to the 15 way I/O connector.

•

Switch the camera on using the ON/OFF switch. You should hear an audible confirmation (a short

beep followed by a long beep)

•

Turn on the PC.

•

Start your software.

•

Start acquiring data.

Figure 38:

Connect the Zyla to the port on the PC by the connections shown above (Left) Camera Link model, (Right) USB 3.0 model

12V 5A

Max

OFF

I/O

USB

3.0

Made in UK

1. I/O 15-Way D Type

Connector

2. CL1 connector
3. CL2 connector (10-tap

cameralink versions only)

4. USB 3.0 Connector

Camera Link Model

USB 3.0 Model

Содержание Zyla sCMOS 4.2 PLUS















































































Результаты поиска

Содержание Zyla sCMOS 4.2 PLUS

Отзывы:

Бренды по названию

Популярные бренды

Andor Technology Zyla sCMOS 4.2 PLUS, Руководство по оборудованию

Результаты поиска

Содержание Zyla sCMOS 4.2 PLUS

Отзывы:

Бренды по названию

Популярные бренды