Anderson STACKPRO 5400 Скачать руководство пользователя страница 60

Страница: 60 / 60

Fault error list

STACKPRO 5400

STACKPRO 7200 1.0 (2015-2018)

STACKPRO 7200 2.0 (2019 AND +)

FAULT #1

COMMUNICATION MC050

FAULT #2

COMMUNICATION IOX024

FAULT #3

COMMUNICATION ANGLE SENSOR

FAULT #4

LOAD SENSING PRESSURE SENSOR

FAULT #5

CLAW PRESSURE SENSOR

FAULT #6

SL PRESSURE SENSOR

FAULT #7

LS_SL_B & LS_SL_H ACTIVE (VERIFY IN MANUAL MODE) Low oil level

LS_SL_B & LS_SL_H ACTIVE (VERIFY IN MANUAL MODE)

FAULT #8

LS_PG_E & LS_PG_R ACTIVE (VERIFY IN MANUAL MODE) High oil temperature

LS_PG_E & LS_PG_R ACTIVE (VERIFY IN MANUAL MODE)

FAULT #9

LS_PO_R ALWAYS ON

Very high oil temperature

LS_PO_R ALWAYS ON

FAULT #10

LS_PD_R ALWAYS ON

LS_SL_B & LS_SL_H active (Verify in manual mode)

LS_PD_R ALWAYS ON

FAULT #11

LS_DP_M IS INACTIVE (VERIFY IN MANUAL MODE)

LS_BR_E & LS_BR_R active (Verify in manual mode)

LS_DP_M IS INACTIVE (VERIFY IN MANUAL MODE)

FAULT #12

LS_PG_E & LS_PG_R active (Verify in manual mode)

LS_SL_M IS INACTIVE (VERIFY IN MANUAL MODE)

FAULT #13

LS_PO_R always ON

FAULT #14

FAULT #15

FAULT #16

FAULT #17

FAULT #18

FAULT #19

FAULT #20

FAULT #21

FAULT #22

OUTPUT-MC050-C1P31-ARM D0WN CHECK VALVE

Output - MC050 - C1P31 - Dumper up

OUTPUT-MC050-C1P31-ARM D0WN CHECK VALVE

FAULT #23

OUTPUT-MC050-C1P32-CLAW SEQ COIL

Output - MC050 - C1P32 - Dumper down

OUTPUT-MC050-C1P32-CLAW SEQ COIL

FAULT #24

OUTPUT-MC050-C1P33-SPARE

Output - MC050 - C1P33 - Carriage down

OUTPUT-MC050-C1P33-SPARE

FAULT #25

OUTPUT-MC050-C1P34-SPARE

Output - MC050 - C1P34 - Carriage up

OUTPUT-MC050-C1P34-SPARE

FAULT #26

OUTPUT-MC050-C1P35-DUMPER DOWN

Output - MC050 - C1P35 - Arm up

OUTPUT-MC050-C1P35-DUMPER DOWN

FAULT #27

OUTPUT-MC050-C1P36-DUMPER UP

Output - MC050 - C1P36 - Arm down

OUTPUT-MC050-C1P36-DUMPER UP

FAULT #28

OUTPUT-MC050-C1P37-ARM DOWN. (S-C)

Output - MC050 - C1P37 - Raising system SIG (S-C)

OUTPUT-MC050-C1P37-ARM DOWN. (S-C)

FAULT #29

OUTPUT-MC050-C1P37-ARM DOWN. (O-C)

FAULT #30

OUTPUT-MC050-C1P38-ARM UP. (S-C)

Output - MC050 - C1P38 - Raising system PWR (S-C)

OUTPUT-MC050-C1P38-ARM UP. (S-C)

FAULT #31

OUTPUT-MC050-C1P38-ARM UP. (O-C)

Output - MC050 - C1P38 - Raising system PWR (O-C)

OUTPUT-MC050-C1P38-ARM UP. (O-C)

FAULT #32

OUTPUT-MC050-C1P39-WRIST RET. (S-C)

Output - MC050 - C1P39 - Ext. dumpeur SIG (S-C)

OUTPUT-MC050-C1P39-WRIST RET. (S-C)

FAULT #33

OUTPUT-MC050-C1P39-WRIST RET. (O-C)

FAULT #34

OUTPUT-MC050-C1P40-WRIST EXT. (S-C)

Output - MC050 - C1P40 - Ext dumper PWR (S-C)

OUTPUT-MC050-C1P40-WRIST EXT. (S-C)

FAULT #35

OUTPUT-MC050-C1P40-WRIST EXT. (O-C)

Output - MC050 - C1P40 - Ext dumper PWR (O-C)

OUTPUT-MC050-C1P40-WRIST EXT. (O-C)

FAULT #36

OUTPUT-MC050-C1P41-CLAW OPEN (S-C)

Output - MC050 - C1P41 - Wrist up (S-C)

OUTPUT-MC050-C1P41-CLAW OPEN (S-C)

FAULT #37

OUTPUT-MC050-C1P41-CLAW OPEN (O-C)

Output - MC050 - C1P41 - Wrist up (O-C)

OUTPUT-MC050-C1P41-CLAW OPEN (O-C)

FAULT #38

OUTPUT-MC050-C1P42-CLAW CLOSE (S-C)

Output - MC050 - C1P42 - Wrist down (S-C)

OUTPUT-MC050-C1P42-CLAW CLOSE (S-C)

FAULT #39

OUTPUT-MC050-C1P42-CLAW CLOSE (O-C)

Output - MC050 - C1P42 - Wrist down (O-C)

OUTPUT-MC050-C1P42-CLAW CLOSE (O-C)

FAULT #40

OUTPUT-MC050-C1P43-SL DOWN (S-C)

Output - MC050 - C1P43 - Pressure control (S-C)

OUTPUT-MC050-C1P43-SL DOWN (S-C)

FAULT #41

OUTPUT-MC050-C1P43-SL DOWN (O-C)

Output - MC050 - C1P43 - Pressure control (O-C)

OUTPUT-MC050-C1P43-SL DOWN (O-C)

FAULT #42

OUTPUT-MC050-C1P44-SL UP (S-C)

Output - MC050 - C1P44 - Pusher ext. (S-C)

OUTPUT-MC050-C1P44-SL UP (S-C)

FAULT #43

OUTPUT-MC050-C1P44-SL UP (O-C)

Output - MC050 - C1P44 - Pusher ext. (O-C)

OUTPUT-MC050-C1P44-SL UP (O-C)

FAULT #44

OUTPUT-MC050-C1P45-CH FORWARD (S-C)

Output - MC050 - C1P45 - Pusher ret. (S-C)

OUTPUT-MC050-C1P45-CH FORWARD (S-C)

FAULT #45

OUTPUT-MC050-C1P45-CH FORWARD (O-C)

Output - MC050 - C1P45 - Pusher ret. (O-C)

OUTPUT-MC050-C1P45-CH FORWARD (O-C)

FAULT #46

OUTPUT-MC050-C1P46-CH BACKWARD (S-C)

FAULT #47

OUTPUT-MC050-C1P46-CH BACKWARD (O-C)

FAULT #48

OUTPUT-IOX024-C2P03-PD EXT. (S-C)

Output - IOX024 - C2P03 - Claw close (S-C)

OUTPUT-IOX024-C2P03-PD EXT. (S-C)

FAULT #49

OUTPUT-IOX024-C2P03-PD EXT. (O-C)

Output - IOX024 - C2P03 - Claw close (O-C)

OUTPUT-IOX024-C2P03-PD EXT. (O-C)

FAULT #50

OUTPUT-IOX024-C2P04-PD RET. (S-C)

Output - IOX024 - C2P04 - Claw open (S-C)

OUTPUT-IOX024-C2P04-PD RET. (S-C)

FAULT #51

OUTPUT-IOX024-C2P04-PD RET. (O-C)

Output - IOX024 - C2P04 - Claw open (O-C)

OUTPUT-IOX024-C2P04-PD RET. (O-C)

FAULT #52

OUTPUT-IOX024-C2P05-PO RET. (S-C)

Output - IOX024 - C2P05 - Forks up (S-C)

OUTPUT-IOX024-C2P05-PO RET. (S-C)

FAULT #53

OUTPUT-IOX024-C2P05-PO RET. (O-C)

Output - IOX024 - C2P05 -Forks up (O-C)

OUTPUT-IOX024-C2P05-PO RET. (O-C)

FAULT #54

OUTPUT-IOX024-C2P06-PO EXT. (S-C)

Output - IOX024 - C2P06 - Forks down (S-C)

OUTPUT-IOX024-C2P06-PO EXT. (S-C)

FAULT #55

OUTPUT-IOX024-C2P06-PO EXT. (O-C)

Output - IOX024 - C2P06 - Forks down (O-C)

OUTPUT-IOX024-C2P06-PO EXT. (O-C)

FAULT #56

OUTPUT-IOX024-C2P07-ED RET. (S-C)

FAULT #57

OUTPUT-IOX024-C2P07-ED RET. (O-C)

FAULT #58

Output - IOX024 - C2P08 - Claw seq coil (S-C)

OUTPUT-IOX024-C2P08-ED EXT. (S-C)

FAULT #59

Output - IOX024 - C2P08 - Claw seq coil (O-C)

OUTPUT-IOX024-C2P08-ED EXT. (O-C)

FAULT #60

Output - IOX024 - C2P09 - Dumper claw close (S-C)

FAULT #61

Output - IOX024 - C2P09 - Dumper claw close (O-C)

FAULT #62

Output - IOX024 - C2P09 - Dumper claw open (S-C)

FAULT #63

Output - IOX024 - C2P09 - Dumper claw open (O-C)

S-C SHORT CIRCUIT
O-C OPEN CIRCUIT

Содержание STACKPRO 5400





























































Результаты поиска

Содержание STACKPRO 5400

Отзывы:

Похожие инструкции для STACKPRO 5400

Бренды по названию

Популярные бренды

Anderson STACKPRO 5400, Руководство по диагностике

Результаты поиска

Содержание STACKPRO 5400

Отзывы:

Похожие инструкции для STACKPRO 5400

Бренды по названию

Популярные бренды