www.Busse-Yachtshop.de - [email protected]
1
2
6
3
5
7
8
9
EXPLODED VIEW
WINCH 28,
VER.1.2
LIMITED WARRANTY
1.1
ANDERSEN issues a three-year warranty on all their products covering manufacturing and
material defects on condition that the products are used in normal fashion. The warranty shall
apply for three years from the moment ANDERSEN sell the product concerned (to the first
buyer).
1.2
Within the period of the warranty, and in accordance with the terms of the warranty, ANDERSEN
undertake to replace or repair all defective components, which have been used in normal
fashion.
1.3
The warranty is however subject to the limitations and exceptions outlined below.
Conditions and limitations:
2.1
ANDERSEN´s liability shall be limited to repair or replacement of components, which are
defective owing to manufacturing or material defects.
2.2
ANDERSEN assume no other liability than this, not even liability for indirect losses caused by
defect concerned, including operating losses, loss of profits, or damage caused to real property
or moveable property occurring while the product concerned is in the possession of the Buyer.
2.3
The Buyer alone shall bear the responsibility and risk involved as to whether the products are
suitable for the application intended. ANDERSEN assume no liability in this connection.
2.4
ANDERSEN assume no liability for defects which occur due to use of their products for purposes
for which they are not intended, or for defects which occur owing to incorrect installation,
corrosion, ultraviolet degradation, lack of maintenance, or any alteration or repair of the product
carried out incorrectly by the Buyer. Finally, ANDERSEN assume no liability for normal wear and
tear, or for depreciation in value.
2.5
ANDERSEN do not assume any liability for service carried out by anyone other than authorised
ANDERSEN representatives, unless such service is carried out pursuant to guidelines laid down
by ANDERSEN and in accordance with good craftsmanship.
2.6
The buyer shall inform ANDERSEN in writing of any defects with no undue delay once defects
have been registered. Products being dealt with under the warranty shall be returned to ANDER-
SEN for repair unless any other agreement has been reached in writing.
2.7
ANDERSEN shall not cover costs incurred by the Buyer in connection with the transport or
wages involved in a warranty case. The Buyer in full shall meet such costs.
Exceptions:
3.1
The warranty is only valid for one year in respect of components bought for the products con-
cerned, such as electric motors, electric equipment, hydraulic pumps, motors and valves.
3.2
ANDERSEN assume no liability for consequential damage of ships, equipment, property or
people caused by defects in ANDERSEN products.
3.3
The company’s products are subject to continuous development, and consequently ANDERSEN
reserve the right to change designs and specifications without prior notice.
MOUNTING INSTRUCTION
WINCH 28,
VER.1.2
1.
Remove circlip (1), using a small sharp screw driver.
2.
Remove drum (2).
3.
Mark location of the bolt holes using the winch base (15) as a tem-
plate.
4.
Remove the winch base. Be sure that no dust comes into contact with
the winch while drilling the bolt holes.
5.
Drill the bolt holes ø6.5mm.
6.
Clean the area.
7.
Apply a light coat of bedding compound, ensuring that each hole is
bedded. Drain grooves should be kept clear.
8.
Fasten the winch base into place using 5 pcs M6 countersunk head
screws.
9.
Assemble in reverse order
10. Check that the winch is functioning correctly.
SERVICE INSTRUCTION
WINCH 28,
VER.1.2
Maintenance interval 1-2 years, depending on operating conditions.
1.
Remove circlip (1).
2.
Remove drum (2).
3.
Remove the black plastic circlip (8).
4.
Remove drive shaft (6).
5.
Remove roller bearings (7,9).
6.
Remove gear shaft (10).
7.
Remove & dismantle the gear unit (11,12,13,14)
8.
Clean all moving parts with benzine.
9.
Check pawls & springs for wear and replace if necessary. In order to
replace the upper pawls (4) or springs (5), the gliding washer (3)
must be removed.
10. Reassemble the winch in reverse order, lightly greasing all moving
parts, with a soft, small brush. We strongly recommend to use only
ANDERSEN Winch Grease for this purpose*
11. Check that the winch is functioning correctly.
*) Most types of grease, including “marine grease” are NOT suitable for lubrication of
winches. None suitable grease can cause mechanical malfunction. Malfunctioning pawls may
lead to unexpected failure of a loaded winch, resulting in material damage or fatal personal
injury.
Service Kit No. 4 (part no. 710004) contains service parts for this winch.
PARTS LIST
WINCH 28,
VER.1.2
POS QTY DESCRIPTION
PART
NO.
1
1
CIRCLIP
712800
2
1
DRUM
730600
3 1 GLIDING
WASHER 718400
4
2
PAWL
533400
5 2 PAWL
SPRING
533500
6
1
DRIVE SHAFT, COMPLETE
711400
7 1 ROLLER
BEARING 712905
8
1
CIRCLIP
716001
9 1 ROLLER
BEARING 712905
10 1 GEAR
SHAFT
711800
11 1 PAWL
GEAR
711600
12
2
PAWL
533400
13 2 PAWL
SPRING
533500
14 1 RATCHET
GEAR
711701
15
1
WINCH
BASE
730700
4
12
11
13
10
14
15
